Foto CIS10 IP68 10Amp Akwụkwọ ntuziaka onye njikwa chaja anyanwụ

1. Okwu mmalite

This manual provides essential instructions for the safe and efficient operation of your Phocos CIS10 IP68 10Amp Solar Charge Controller. The CIS10 is designed for off-grid solar light systems and battery charging, featuring automatic 12V/24VDC system voltage detection and a robust IP68 waterproof design. Please read this manual thoroughly before installation and use.

2. Ozi nchekwa

Ntuziaka nchekwa dị mkpa:

• Always connect the battery to the charge controller first, then the solar panel, and finally the load. Disconnect in the reverse order.
• Ensure all connections are tight and secure to prevent excessive voltage drop and loose connections.
• Install the controller in a well-ventilated area, away from flammable gases.
• Emela ka onye njikwa ahụ gbawaa ma ọ bụ gbalịa ịrụzi ya n'onwe gị. Kpọtụrụ ndị ọrụ ruru eru maka ọrụ ahụ.
• Wear appropriate personal protective equipment (PPE) when working with batteries and solar panels.
• The controller is IP68 rated for water and dust ingress, but avoid submerging it for extended periods or exposing it to high-pressure water jets.

3. Akụrụngwa Ngwaahịa

The Phocos CIS10 Solar Charge Controller offers the following key features:

• IP68 Igwe anaghị egbochi mmiri: Suitable for outdoor use, resistant to water spray, rain, and condensation.
• Akpaaka Voltage Nchọpụta: Na-achọpụta 12V ma ọ bụ 24V DC sistemụ voltages.
• 5-Stage PWM Technology: Provides Soft Start, Bulk, Absorption, Float, and Equalization charging stages for optimal battery health and system performance.
• Ndakọrịta Batrị zuru oke: Works with LifePo4, LTO, GEL, AGM, Lead-Acid, Calcium, and EFB batteries.
• Atụmatụ nchekwa ọtụtụ: Built-in protection against over-temperature, over-voltage, over-current, over-charging, over-discharging, overload, and short circuits.
• Compact and Thin Design: Maximizes solar power utilization with minimal self-power consumption.

4. Ntọala na nwụnye

Follow these steps for proper installation of your Phocos CIS10 controller:

1. Ịkwanye: Choose a suitable location for mounting the controller. Although IP68 rated, mounting in a shaded or protected area can extend its lifespan. Ensure adequate space for cable connections.
2. Njikọ batrị: Connect the battery cables to the controller's battery terminals first. Ensure correct polarity (positive to positive, negative to negative). The controller will automatically detect the system voltage (12V ma ọ bụ 24V).
   

   Image 4.1: Phocos CIS10 controller showing battery, solar panel, and load connection points, along with LED indicators for status.

3. Njikọ anyanwụ panel: Connect the solar panel cables to the controller's solar panel terminals. Observe correct polarity. The controller will begin charging the battery.
4. Njikọ Ibu (Nhọrọ): If using the controller for a DC load (e.g., solar light), connect the load cables to the controller's load terminals. Ensure correct polarity.
5. Nyochaa njikọ: Double-check all connections for tightness and correct polarity before powering on the system.

The controller's compact design and integrated wiring simplify installation. Its IP68 rating ensures durability in various outdoor conditions.

Image 4.2: The Phocos CIS10 controller demonstrating its compact size with a ruler and highlighting its IP68 waterproof capability.

5. Ntuziaka ọrụ

The Phocos CIS10 operates automatically once connected. It utilizes advanced 5-stage Pulse Width Modulation (PWM) charging technology to optimize battery charging and extend battery life.

5.1. Ịchaji Stages

• Mmalite dị nro: Gradually increases current to the battery.
• Nnukwu ego: Delivers maximum current to rapidly charge the battery to approximately 80% capacity.
• Ụgwọ mmịpụta: Charges the battery at a constant voltage to bring it to 100% capacity.
• N'elu mmiri n'Aka: Na-edobe batrị ahụ n'ọkụ zuru oke site n'inye obere vol na-agbanwe agbanwetage.
• Nhata: Automatically performs equalization every 28 days for calcium/EFB batteries to prevent sulfation and ensure cell balance.

5.2. Work Mode (Optional)

The CIS10 controller supports configurable work modes, such as time control and light control, which can be set using an optional external unit like the CIS-CU (sold separately). This allows for customized operation of connected loads, such as solar lights.

6. Nlekọta

The Phocos CIS10 is designed for minimal maintenance due to its robust IP68 rating and epoxy-encapsulated PCB. However, periodic checks are recommended:

• Nlele anya: Periodically inspect the controller and all connections for any signs of damage, corrosion, or loose wiring.
• Nhicha: If necessary, gently clean the exterior of the controller with a damp akwa . Ejila kemịkalụ siri ike ma ọ bụ ihe abrasive.
• Ahụike batrị: Monitor your battery's performance. The controller's equalization feature helps maintain battery health for compatible types.

7. Nchọpụta nsogbu

The CIS10 controller includes multiple built-in protections to prevent damage. If you encounter issues, consider the following:

• No Charging/Load Output:
  • Check all wiring connections for tightness and correct polarity.
  • Gbaa mbọ hụ na akụkụ anyanwụ na-enweta ìhè anyanwụ zuru oke.
  • Nyochaa voltaji batrịtage is within the operating range (12V/24V).
  • Check for any blown fuses in the system (if applicable).
• Nchekwa oke okpomọkụ: If the controller becomes excessively hot, it may temporarily reduce or stop charging/output. Ensure it's not installed in an area with poor ventilation or direct, intense heat.
• N'elu-Voltage/N'okpuru-Voltage Nchedo: The controller will protect the battery from overcharging or deep discharge. If the battery voltage is too low, the load may be disconnected.
• Short Circuit/Overload Protection: If a short circuit or overload occurs on the load or solar input, the controller will temporarily shut down to protect itself and the system. Remove the fault and the controller should resume normal operation.

If problems persist, refer to the detailed specifications or contact Phocos customer support.

8. Nkọwapụta

Detailed technical specifications for the Phocos CIS10 Solar Charge Controller:

9. Akwụkwọ ikike na nkwado

Phocos is a German brand known for quality assurance in solar power products. For warranty information, technical support, or service inquiries, please contact your authorized Phocos dealer or visit the official Phocos websaịtị. Debe akwụkwọ nnata ịzụrụ maka akwụkwọ ikike.

For additional resources and product updates, you may visit the Phocos official websaịtị.