1. Okwu mmalite
This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your KERN PFB 600-2 Precision Laboratory Balance. Please read these instructions carefully before using the device to ensure accurate measurements and prolong its lifespan.
2. Ozi nchekwa
- Always operate the balance on a stable, level surface free from vibrations.
- Avoid exposing the balance to extreme temperatures, direct sunlight, or high humidity.
- Do not overload the balance beyond its maximum capacity of 600g.
- Keep liquids and corrosive substances away from the balance.
- Jiri naanị nkwụnye ọkụ enyere.
3. Nhazi
3.1 Mwepu na nyocha
Carefully remove the balance from its packaging. Inspect all components for any signs of damage. The package should contain the balance unit, weighing pan, draft shield (if applicable), and power adapter.
This image displays the KERN PFB 600-2 Precision Laboratory Balance. It features a white and blue casing, a circular weighing pan, and a clear glass draft shield. The digital display shows '0.00 g', and control buttons for 'PRINT/ESC', 'MODE', 'PCS', '%', 'TARE', and 'ON/OFF' are visible on the front panel.
3.2 Ntinye na ọkwa
- Place the balance on a firm, level, and vibration-free surface.
- Adjust the leveling feet located at the bottom of the balance until the air bubble in the spirit level (usually located near the display) is centered.
3.3 Njikọ ike
Connect the power adapter to the balance and then plug it into a suitable power outlet. Allow the balance to warm up for at least 30 minutes before initial use for optimal accuracy.
4. Ntuziaka ọrụ
4.1 Gbanyụọ ma ọ bụ gbanyụọ
- Pịa Gbanye/ Gbanyụọ button to turn the balance on.
- Pịa ma jide Gbanye/ Gbanyụọ button to turn the balance off.
4.2 Ibu Ibu Dị Mkpa
- Ensure the balance is level and the display shows '0.00 g'. If not, press the NA-EGO button ka efu ngosi.
- Carefully place the item to be weighed onto the center of the weighing pan.
- Read the stable weight value displayed.
4.3 Tare arụ ọrụ
The tare function allows you to weigh items in a container without including the container's weight.
- Place the empty container on the weighing pan.
- Pịa NA-EGO button. The display will show '0.00 g'.
- Add the substance to be weighed into the container. The display will show only the net weight of the substance.
4.4 Ngbanwe nkeji
Pịa MODE button to cycle through available weighing units (e.g., grams, ounces, pounds, carats, etc.). The active unit will be indicated on the display.
4.5 Ọrụ Ngụkọta (PCS)
This function allows for counting a large number of identical items.
- Place a known quantity of items (e.g., 10, 20, 50, 100 pieces) on the pan.
- Pịa PCS bọtịnụ. Ngosipụta ahụ ga-akpali gị ịhọrọ sample size.
- Jiri ihe MODE or % buttons to select the corresponding sample size (e.g., P10 for 10 pieces).
- Pịa PCS again to confirm. The balance is now in counting mode.
- Add more items, and the display will show the total count.
Pasent 4.6tage Weighing (%)
This function allows you to determine the percentage of a sample relative to a reference weight.
- Debe ntụaka sample na pan a na-atụ.
- Pịa % button. The display will show '100.00%'.
- Wepu akwụkwọ ntụaka sample ma tinye sample to be measured. The display will show its weight as a percentage of the reference sample.
4.7 Print Function
If connected to a compatible printer or PC, pressing the PRINT/ESC button will send the current weighing data to the connected device.
5. Nlekọta
5.1 Nhicha
- Kwupu ike mgbe niile tupu ihicha.
- Wipe the balance exterior with a soft, damp akwa . Jiri ncha dị nro ma ọ dị mkpa.
- Do not use abrasive cleaners, solvents, or immerse the balance in water.
- Clean the weighing pan regularly to prevent accumulation of dust or debris.
5.2 Nchekwa
When not in use for extended periods, store the balance in a dry, dust-free environment at room temperature. Ensure the draft shield is in place to protect the weighing mechanism.
5.3 Nhazigharị
Periodic calibration with certified weights is recommended to maintain accuracy. Refer to the balance's specific calibration procedure in the full technical manual or contact KERN support for guidance.
6. Nchọpụta nsogbu
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Display shows 'Err' or 'Overload' | Ibu karịrị ikike kachasị. | Wepu oke ibu. |
| Ọgụgụ na-ezighi ezi | Balance not level, vibrations, temperature fluctuations, need for calibration. | Check leveling, move to stable surface, allow warm-up, perform calibration. |
| Ngosipụta anaghị agbanwu | No power, faulty adapter. | Check power connection, try a different outlet, verify adapter functionality. |
| Display shows '0.00' but weight is on pan | Tare function was activated with item on pan. | Remove item, press NA-EGO to zero, then re-weigh. |
7. Nkọwapụta
| Njirimara | Nkọwa |
|---|---|
| Nọmba nlereanya | PFB 600-2 |
| Ike kacha | 600 g |
| Akụkụ ngwaahịa | 12.4 x 8.27 x 3.54 sentimita asatọ |
| Ibu Ibu | 4.41 pound |
| Ụdị ngosi | Dijitalụ |
| Atụmatụ pụrụ iche | High Precision, High Weight Capacity, Digital Display |
| Eji akwadoro | Laboratory/Scientific Applications, Jewellery |
8. Akwụkwọ ikike Ozi
KERN products are manufactured to high-quality standards. This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and duration, please refer to the warranty card included with your product or visit the official KERN websaịtị. Debe nnata nzụta gị ka ihe akaebe nke ịzụrụ.
9. Nkwado
For technical assistance, service, or further inquiries regarding your KERN PFB 600-2 Precision Laboratory Balance, please contact KERN customer support. Contact details can typically be found on the KERN official websaịtị ma ọ bụ na akwụkwọ enyere na ịzụrụ gị.
