Tecnolite LED-12V-360W-PR 360W Power Supply Driver User Manual

1. Okwu mmalite

This manual provides detailed instructions for the safe and efficient use of the Tecnolite LED-12V-360W-PR 360W Power Supply Driver. This device is designed for project applications, converting AC input voltage to a stable 12V DC output for LED lighting systems and other compatible devices. Please read this manual thoroughly before installation and operation.

Foto 1: Tecnolite LED-12V-360W-PR 360W Power Supply Driver. This image shows the aluminum casing, ventilation slots, input/output terminals, and voltage nhọrọ mgba ọkụ.

2. Ozi nchekwa

Na-edebe nchekwa nchekwa ndị a mgbe niile iji gbochie mmerụ ahụ ma ọ bụ mebie ngwaọrụ:

• Kpachara anya! Elu VolTAGE N'ime. Do not remove this cover. Only qualified service personnel should perform maintenance or repairs.
• Gbaa mbọ hụ na ntinye voltage switch (115V/230V) is correctly set before connecting to the power source to avoid damaging the unit.
• Gbanyụọ ike tupu ịme njikọ ma ọ bụ mgbanwe ọ bụla.
• Install the driver in a well-ventilated area to prevent overheating.
• Ekpughela ngwaọrụ ahụ na mmiri mmiri ma ọ bụ oke okpomọkụ.
• Ensure proper grounding (indicated by the # symbol on the terminal block).
• Agafela ikike ibu kacha nke 360W.

3. Akụrụngwa Ngwaahịa

• Designed for project applications.
• Ntinye sara mbara voltage range: 100-277 VAC.
• Ihe nrụpụta kwụsiri ike voltage: 12 VDC.
• High power output: 360 W maximum load.
• Durable aluminum casing for heat dissipation and protection.
• Integrated drivers for efficient power conversion.

4. Ntọala na nwụnye

1. Iwepu: Carefully remove the power supply from its packaging and inspect for any physical damage.
2. Ịkwanye: Mount the driver securely in a location that allows for adequate ventilation. Ensure no obstructions block the ventilation slots.
3. Ntinye Voltage Nhọrọ: Chọta voltage selection switch on the side of the unit. Set it to either 115V or 230V according to your local mains voltage. Incorrect selection can damage the unit.
4. Wiring Input (AC): Connect the AC input wires to the terminal block labeled 'L' (Live), 'N' (Neutral), and '#' (Ground). Ensure all connections are tight and secure.
5. Wiring Output (DC): Connect your 12V DC load (e.g., LED strips, modules) to the output terminals labeled '+V' and '-V'. Observe correct polarity (+ to + and - to -).
6. Nyocha ikpeazụ: Double-check all connections and the input voltage selection before applying power.

5. Ntuziaka ọrụ

Once the power supply is correctly installed and wired, you can apply power. The unit will convert the AC input to a stable 12V DC output. The output voltage can be finely adjusted using the '+V ADJ' potentiometer if necessary, though it is typically pre-calibrated.

• Ensure the total power consumption of connected devices does not exceed 360W.
• Monitor the unit for any unusual noises or excessive heat during initial operation.

6. Nlekọta

The Tecnolite LED-12V-360W-PR driver requires minimal maintenance. Follow these guidelines to ensure longevity:

• Debe ihe dị n'ime ya ọcha ma ghara ịta uzuzu na ihe ruru unyi. Jiri ákwà dị nro ma kpọọ nkụ hichaa ya.
• Periodically check ventilation openings to ensure they are not blocked.
• Inspect wiring connections for tightness and signs of wear or corrosion.
• Anwala imepe casing, as it contains high voltage components and should only be serviced by qualified personnel.

7. Nchọpụta nsogbu

8. Nkọwapụta

9. Akwụkwọ ikike na nkwado

For warranty information or technical support, please contact Tecnolite customer service or visit the official Tecnolite brand store.

Tecnolite Brand Store: Tecnolite on Amazon.com.mx