Leviton 003-84026-0 Stainless Steel 2-Gang Power Outlet Receptacle Wallplate Instruction Manual

Okwu mmalite

This manual provides instructions for the proper installation and maintenance of the Leviton 003-84026-0 Stainless Steel 2-Gang Power Outlet Receptacle Wallplate. Please read these instructions carefully before beginning installation.

Ozi nchekwa

• Always turn off power at the circuit breaker or fuse box before installation or maintenance.
• Ensure all wiring connections comply with local electrical codes.
• Ọ bụrụ na ịmaghị maka akụkụ ọ bụla nke ntuziaka ndị a, kpọtụrụ onye ọrụ ọkụ eletrik tozuru etozu.
• Emebere ngwaahịa a maka naanị ime ụlọ.

Ihe ngwugwu

• Leviton 003-84026-0 Stainless Steel 2-Gang Wallplate
• Mounting Screws (typically included with wallplate)

Ntọala na nwụnye

1. Gbanyụọ ike: Locate the circuit breaker or fuse that controls the power to the outlet where the wallplate will be installed. Turn off the power completely. Verify power is off using a voltagọ bụ onye nyocha.
2. Wepụ Mgbidi Ochie: Carefully unscrew and remove the existing wallplate, if any.
3. Ọnọdụ Mgbidi Ọhụrụ: Align the Leviton 003-84026-0 wallplate over the electrical box, ensuring the openings match the receptacles.
4. Mgbidi echekwara: Insert the provided mounting screws into the designated holes on the wallplate and tighten them gently until the wallplate is flush with the wall. Do not overtighten, as this can damage the wallplate or the electrical box.
5. Weghachi ike: Once the wallplate is securely installed, restore power at the circuit breaker or fuse box.

Ntuziaka ọrụ

The Leviton 003-84026-0 wallplate is a passive component designed to cover and protect electrical outlets. No specific operational steps are required beyond its proper installation. Ensure that the receptacles are fully accessible and that the wallplate does not obstruct their use.

Nlekọta

• Nhicha: To clean the stainless steel wallplate, use a soft, damp cloth. For stubborn marks, a mild, non-abrasive cleaner suitable for stainless steel can be used. Avoid harsh chemicals or abrasive scrubbers, which can scratch the finish.
• Nyocha: Periodically inspect the wallplate for any signs of damage, such as cracks, discoloration, or loose screws. If damage is observed, turn off power and replace the wallplate.

Nchọpụta nsogbu

• Wallplate is Loose: Ensure mounting screws are tightened appropriately. Do not overtighten.
• Wallplate Does Not Sit Flush: Check for obstructions behind the wallplate or ensure the electrical box is properly recessed.
• Scratches or Discoloration: Refer to the Maintenance section for cleaning instructions. Deep scratches may require replacement.

Nkọwapụta

This diagram illustrates the precise dimensions of the 2-gang wallplate. It shows a width of 2.750 inches (69.85 mm) for each opening, a total width of 4.56 inches (115.9 mm) for the 2-gang configuration, and a height of 4.500 inches (114.30 mm). The thickness is 0.220 inches (5.59 mm). Screw hole spacing and opening dimensions are also detailed.

Ozi akwụkwọ ikike

Leviton products are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Leviton websaịtị ma ọ bụ kpọtụrụ ndị ahịa. Debe ihe akaebe nke ịzụrụ ihe gị maka nkwupụta nkwa.

Nkwado na kọntaktị

For technical assistance, product inquiries, or support, please visit the official Leviton webweebụsaịtị ma ọ bụ kpọtụrụ ngalaba ọrụ ndị ahịa ha. Enwere ike ịchọta ozi kọntaktị na nke onye nrụpụta webngwugwu saịtị ma ọ bụ ngwaahịa.

• Onye nrụpụta: Leviton
• Websaịtị: www.leviton.com