TROTEC TA300 Anemometer User Manual

1. Okwu mmalite

The TROTEC TA300 is a professional hot-wire anemometer designed for precise measurement of air velocity, air temperature, and volumetric flow. Its practical telescopic probe allows for versatile applications, including measurements in ducts and hard-to-reach areas. This instrument combines a robust thermal wire sensor with advanced microprocessor technology to ensure fast and accurate results.

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your TA300 anemometer. Please read it thoroughly before using the device.

Image 1: TROTEC TA300 Anemometer main unit and telescopic probe. The display shows 'VEL 3.11 m/s' and 'TEMP 22.2 °C'.

2. Ozi nchekwa

Na-agbaso ihe ndị a dị mkpa mgbe niile iji gbochie mmerụ ahụ na mmebi nke ngwaọrụ ahụ:

• Gụọ akwụkwọ ntuziaka dum tupu arụ ọrụ.
• Ejila ngwaọrụ ahụ rụọ ọrụ n'ebe ihe na-agbawa agbawa ma ọ bụ n'ebe ihe ndị nwere ike ire ọkụ dị nso.
• Zere ikpughe ngwaọrụ ahụ na oke okpomọkụ, ìhè anyanwụ kpọmkwem, ma ọ bụ oke iru mmiri.
• Do not attempt to modify or disassemble the device. Repairs should only be performed by authorized personnel.
• Debe ngwaọrụ ahụ ka ụmụaka ghara iru ya.
• Ensure the telescopic probe is handled with care to prevent bending or damage to the sensor.

3. Ihe ngwugwu

Nyochaa na ihe niile dị na adịghị emebi emebi mgbe ebupụ ya:

• TROTEC TA300 Anemometer
• Telescopic hot-wire probe
• Asambodo mmezi
• Akwụkwọ ntuziaka (akwụkwọ a)
• Carrying case (if included with your model)

4. Akụrụngwa Ngwaahịa

The TROTEC TA300 Anemometer offers the following key features:

• Ntụnye ziri ezi: Accurately determines air velocity, air temperature, and volumetric flow.
• Telescopic Probe: Extendable up to 1 meter for measurements in ducts and hard-to-reach locations.
• Robust Sensor: Equipped with a durable thermal wire sensor.
• Advanced Microprocessor: Ensures fast and precise signal processing.
• Ngosipụta LCD backlit: Easy readability even in poorly lit environments.
• Ọrụ njide data: Freezes the current measurement value on the display.
• Min/Max Value Indication: Displays minimum and maximum recorded values.
• Average Value Calculation: Calculates spot and time-averaged values.
• Volumetric Flow Area Input: Easily specify the cross-sectional area for volumetric flow calculations.
• Gbanyụọ ike akpaaka: Na-echekwa ndụ batrị.
• Asambodo mmezi: Included as standard for professional assurance.

Foto 2: Zuru ezu view of the TA300 control buttons and LCD display.

5. Nhazi

5.1. Ntinye batrị

The TA300 anemometer typically uses a 9V block battery. To install or replace the battery:

1. Chọta mkpuchi nke ebe batrị dị n'azụ ngwaọrụ ahụ.
2. Open the cover by sliding or unscrewing it (refer to the diagram if available).
3. Insert a new 9V battery, ensuring correct polarity.
4. Mechie mkpuchi nke batrị batrị nke ọma.

Foto 3: Elu-ala view of the TA300, illustrating the main unit and probe connection area.

5.2. Attaching the Probe

The telescopic hot-wire probe connects to the main unit via a cable.

1. Carefully insert the probe's connector into the designated port on the main unit.
2. Ensure the connection is firm to prevent signal loss during measurement.

5.3. Ike izizi

Pịa bọtịnụ ike (⑂) to turn on the device. The display will illuminate, and the device will perform a self-test before showing measurement readings.

6. Ntuziaka ọrụ

6.1. Extending the Telescopic Probe

The probe can be extended up to 1 meter for reaching measurement points.

1. Gently pull the probe tip to extend it to the desired length.
2. Zere oke ike iji gbochie mmebi.
3. Ensure the probe is fully retracted when not in use to protect the sensor.

Image 4: Extended telescopic probe tip with hot-wire sensor.

6.2. Ụdị nha

The TA300 can measure air velocity, temperature, and volumetric flow.

• Air Velocity (VEL): The primary measurement displayed in m/s, ft/min, km/h, or mph.
• Okpomọkụ (TEMP): Measured simultaneously with air velocity, displayed in °C or °F.
• Volumetric Flow (FLOW): Calculated based on air velocity and a user-defined cross-sectional area.

6.3. Na-agbanwe nkeji

Pịa "Nkeji" button to cycle through available measurement units for velocity and temperature.

6.4. Setting Volumetric Flow Area

To measure volumetric flow, you must input the cross-sectional area of the duct or opening:

1. Pịa "FLOW/TEMP" button to switch to volumetric flow mode.
2. Jiri "MELITE" button to enter the area setting menu.
3. Adjust the area value using the arrow buttons and confirm with "Banye".

6.5. Using Hold, Min/Max, and Mean Functions

• Jide: Pịa "Jide/ZERO" to freeze the current display reading. Press again to release.
• Nkeji/Max: Pịa "MAX/MIN" to view the minimum or maximum recorded values during a measurement session.
• Pụtara: Pịa "ỤMỤ" to calculate and display the average value over a period or series of spot measurements.

7. Nlekọta

7.1. Nhicha

Keep the device clean to ensure optimal performance.

• Jiri ihe dị nro hichaa isi ihe, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
• The hot-wire sensor on the probe is delicate. Clean it only with a soft brush or compressed air, if absolutely necessary, and with extreme care. Avoid touching the sensor directly.

7.2. Nchekwa

When not in use, store the TA300 in its protective carrying case in a dry, dust-free environment, away from extreme temperatures.

• Ensure the telescopic probe is fully retracted before storage.
• Wepụ batrị ahụ ma ọ bụrụ na a gaghị eji ngwaọrụ ahụ ruo ogologo oge iji gbochie mmiri ịpụ apụ.

7.3. nhazi nhazi

The TA300 comes with a factory calibration certificate. For continued accuracy, periodic recalibration by an authorized service center is recommended, especially for professional applications.

8. Nchọpụta nsogbu

If you encounter issues with your TROTEC TA300, refer to the following table:

If the problem persists after attempting these solutions, please contact TROTEC customer support.

9. Nkọwapụta

Technical data for the TROTEC TA300 Anemometer:

10. Akwụkwọ ikike na nkwado

10.1. Akwụkwọ ikike Ozi

The TROTEC TA300 Anemometer is covered by a manufacturer's warranty. Please refer to the warranty card included with your product or visit the official TROTEC websaịtị maka usoro na ọnọdụ zuru ezu. Debe ihe akaebe nke ịzụrụ ihe gị maka nkwupụta nkwa.

10.2. Nkwado ndị ahịa

For technical assistance, service, or spare parts, please contact TROTEC customer support:

• Websaịtị: www.trotec.com (Lelee maka ozi kọntaktị mpaghara)
• Email: Tụtụ aka na website for specific contact forms or email addresses.
• Ekwentị: Tụtụ aka na websaịtị maka nọmba ekwentị mpaghara.

When contacting support, please have your model number (TA300) and serial number (if applicable) ready.