Okwu mmalite
This manual provides comprehensive instructions for the operation and maintenance of your Sharp SPC500 LCD Alarm Clock. Please read this manual thoroughly before use to ensure proper functionality and longevity of your device.
Foto 1: N'ihu view of the Sharp SPC500 LCD Alarm Clock, showing the digital time display and the Sharp logo.
Melite
1. Ntinye batrị
The Sharp SPC500 LCD Alarm Clock operates on two (2) AAA batteries (not included). Ensure correct polarity when inserting the batteries.
- Locate the battery compartment cover on the back or bottom of the clock.
- Wepu mkpuchi.
- Tinye batrị AAA ọhụrụ abụọ, nke kwekọrọ na njedebe (+) na (-) dịka egosiri n'ime ngalaba ahụ.
- Dochie mkpuchi nke batrị batrị nke ọma.
2. Ntọala Oge Mmalite
After installing batteries, the display may flash or show a default time. Proceed to set the current time.
Ntuziaka ọrụ
Isetịpụ Oge Ugbu A
- Locate the "TIME SET" button, usually on the back or side of the clock. Press and hold it until the time display begins to flash.
- Use the "HOUR" and "MINUTE" buttons (often labeled with arrows or +/-) to adjust the hours and minutes. Pay attention to the AM/PM indicator.
- Press "TIME SET" again to confirm the time and exit the setting mode.
Ịtọ oge mkpu
- Locate the "ALARM SET" button. Press and hold it until the alarm time display begins to flash.
- Use the "HOUR" and "MINUTE" buttons to adjust the desired alarm time. Observe the AM/PM indicator.
- Press "ALARM SET" again to confirm the alarm time.
- Ensure the alarm is activated by sliding the "ALARM ON/OFF" switch or pressing the "ALARM ON" button. An alarm icon (e.g., a bell) should appear on the display.
Ọrụ Snooze na Backlight
- Soo: When the alarm sounds, press the large "SNOOZE/LIGHT" button on top of the clock to temporarily silence the alarm. The alarm will sound again after a few minutes (typically 5-9 minutes).
- Ìhè azụ: The clock features a backlight on demand. Press the "SNOOZE/LIGHT" button to illuminate the display for a few seconds, allowing you to view the time in low-light conditions.
Atụmatụ
- 0.5" LCD display for clear time visibility.
- Ascending alarm volume, starting softly and gradually increasing to ensure you wake up.
- Backlight on demand for easy viewna-abanye n'ọchịchịrị.
- Compact and portable design, ideal for travel or bedside use.
Nchọpụta nsogbu
| Nsogbu | Ihe kpatara/ Ngwọta nwere ike ime |
|---|---|
| Ngosipụta bụ oghere ma ọ bụ nchara nchara. |
|
| Alarm does not sound or is too quiet. |
|
| Backlight does not stay on. |
|
| Oge ezighi ezi. |
|
Nkọwapụta
| Ụdị | Nkọ |
| Nlereanya | SPC500 |
| Ụdị ngosi | Dijitalụ LCD |
| Isi Iyi Ike | Batrị nwere ike (batrị AAA 2 x, etinyeghị ya) |
| Atụmatụ pụrụ iche | Alarm, Backlight on demand, Ascending alarm volume |
| Akụkụ (L x W x H) | 9.53 x 6.22 x 5.08 cm (3.75 x 2.45 x 2 inches approx.) |
| Ibu | 68.04 g (2.4 oz approx.) |
Nlekọta
To ensure the longevity and proper functioning of your Sharp SPC500 LCD Alarm Clock, follow these simple maintenance guidelines:
- Nhicha: Wipe the clock's exterior with a soft, dry cloth. Do not use abrasive cleaners, waxes, or solvents as they may damage the finish.
- Ngbanwe batrị: Replace batteries promptly when the display becomes dim or the clock stops functioning correctly. Remove batteries if the clock will not be used for an extended period to prevent leakage.
- gburugburu: Avoid exposing the clock to extreme temperatures, direct sunlight, high humidity, or dusty environments.
Akwụkwọ ikike na nkwado
The Sharp SPC500 LCD Alarm Clock comes with a Akwụkwọ ikike dị afọ 1 site na ụbọchị ịzụrụ ya. Akwụkwọ ikike a na-ekpuchi ntụpọ nrụpụta n'oge ojiji nkịtị.
For warranty claims, technical support, or further assistance, please contact Sharp customer service. Refer to the official Sharp websaịtị ma ọ bụ akwụkwọ ịzụrụ ihe maka ozi kọntaktị kacha ugbu a.
Biko dowe ihe akaebe nke ịzụrụ ihe maka ebumnuche ikike.
