Rectorseal 55912 PR-1L Purple Low VOC Hi-Etch PVC and CPVC Primer Instruction Manual

1. Ngwaahịa gafereview

Rectorseal PR-1L is a purple, low VOC, hi-etch primer specifically formulated for all PVC and CPVC pipe applications. This includes potable water, pressure pipe, gas, conduit, sewers, and drain, waste, and vent (DWV) systems. Its distinctive purple color provides a visual check for complete coverage, ensuring proper surface preparation for superior bonding strength. The primer is LEED Compliant, NSF approved for potable water systems, and meets ASTM F 656 specifications.

Image 1.1: A can of Rectorseal 55912 PR-1L Purple Low VOC Hi-Etch PVC and CPVC Primer.

Akụkụ ndị bụ isi:

• Hi-etch primer for use on both PVC and CPVC pipe, tubing, and socket-type fittings.
• Purple color ensures easy visual check for complete coverage.
• Fast-acting formula prepares surfaces for superior bonding strength.
• LEED Compliant and NSF approved for potable water systems.
• Meets ASTM F 656 specifications.
• Low VOC (Volatile Organic Compound) formulation.

2. Ozi nchekwa

IHE EGWU: Highly Flammable. Vapors may cause flash fire. Harmful or fatal if swallowed. May cause severe eye and skin irritation.

Mkpachapụ anya:

• Use with adequate ventilation. Avoid breathing vapors.
• Wear appropriate personal protective equipment, including safety glasses or goggles and chemical-resistant gloves.
• Keep away from heat, sparks, and open flames. Do not smoke during use.
• Store in a cool, dry, well-ventilated area. Keep container tightly closed when not in use.
• Debe ebe ụmụaka na-apụghị iru.

Mgbata ọsọ enyemaka mbụ:

• Kpọtụrụ anya: Flush immediately with plenty of water for at least 15 minutes and get medical attention.
• kọntaktị akpụkpọ: Wash with soap and water. If irritation persists, seek medical attention.
• iku ume: Remove to fresh air. If breathing is difficult, administer oxygen and get medical attention.
• Ntinye: Do NOT induce vomiting. Call a physician or poison control center immediately.

3. Nkwadebe

Proper preparation is crucial for a strong, leak-free joint. Follow these steps before applying the primer:

1. Cut Pipe: Cut the pipe square using a suitable pipe cutter.
2. Deburr and Chamfer: Remove all burrs from the inside and outside edges of the pipe. Chamfer the end of the pipe to facilitate insertion into the fitting.
3. Ihu igwe dị ọcha: Ensure all pipe and fitting surfaces are clean, dry, and free from dirt, grease, oil, and moisture. Use a clean, dry cloth to wipe surfaces.
4. Dry Fit: Dry fit the pipe and fitting to ensure proper alignment and an interference fit. The pipe should enter the fitting socket easily by 1/3 to 2/3 of the socket depth.

4. Ntuziaka ngwa

Apply Rectorseal PR-1L primer and solvent cement according to the following procedure:

1. Apply Primer to Pipe: Using a natural bristle brush or dauber, apply a liberal and uniform coat of PR-1L primer to the pipe surface, covering an area equal to the depth of the fitting socket. Ensure the entire surface is wetted and purple in color.
2. Apply Primer to Fitting: Immediately apply a liberal and uniform coat of PR-1L primer to the inside of the fitting socket. Ensure complete coverage.
3. Apply Solvent Cement: While the primer is still wet (do not allow primer to dry), immediately apply the appropriate PVC or CPVC solvent cement to both the primed pipe end and the primed inside of the fitting socket. Follow the solvent cement manufacturer's instructions for application.
4. Assemble Joint: Quickly insert the pipe into the fitting socket, twisting a quarter turn until the pipe bottoms out. Hold the joint together firmly for at least 30 seconds to ensure initial set and prevent the pipe from backing out.
5. Remove Excess: Wipe off any excess cement from the joint using a clean cloth.
6. Oge ọgwụgwọ: Allow adequate cure time before handling or pressure testing the joint. Refer to the solvent cement manufacturer's recommendations for specific cure times, which vary based on pipe size, temperature, and humidity.

5. Cleanup and Storage

Hichapụ:

Clean tools and spills immediately with an appropriate solvent cleaner. Ensure proper ventilation during cleanup.

Nchekwa:

Store Rectorseal PR-1L primer in its original container, tightly closed, in a cool, dry, well-ventilated area. Keep away from direct sunlight, heat sources, sparks, and open flames. Do not store above 110°F (43°C). Ensure the container is sealed when not in use to prevent evaporation and maintain product effectiveness.

6. Nchọpụta nsogbu

7. Nkọwapụta

8. Akwụkwọ ikike na nkwado

Rectorseal products are manufactured to high-quality standards. For specific warranty information or technical support, please contact Rectorseal directly or visit their official website. You can also find more information and browse other products at the Rectorseal Brand Store.