Ntuziaka Ntuziaka Gude Flux-Cored Welder SG 120 A

1. Okwu mmalite

This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your Gude Flux-Cored Welder SG 120 A. Please read this manual thoroughly before using the device to ensure proper handling and to prevent injury or damage.

2. Ntuziaka nchekwa

Welding operations involve significant risks. Adhere to all safety precautions to prevent electric shock, burns, fire, and exposure to harmful fumes and radiation.

• Always wear appropriate personal protective equipment (PPE), including a welding helmet with suitable shade, welding gloves, and protective clothing.
• Ensure the welding area is well-ventilated to disperse fumes.
• Etinyela ihe ndị na-ere ọkụ ma ọ bụ mmiri ọkụ n'akụkụ ya.
• Ensure the welder is properly grounded.
• Gbanyụọ ike tupu ị rụzie ma ọ bụ gbanwee ihe ndị ọzọ.
• Emetụkwala akụkụ eletrik dị ndụ aka.
• Debe ụmụaka na ndị ọrụ na-enweghị ikike ka ha ghara ịnọ n'ebe a na-agba ọkụ.
• The machine is equipped with overheating protection. Allow the unit to cool down if it activates.

3. Ngwaahịa gafereview na akụrụngwa

The Gude Flux-Cored Welder SG 120 A is designed for flux-cored welding without the need for shielding gas. It includes the main welding unit, a welding torch, a ground clamp, and basic accessories.

Foto 1: Gude Flux-Cored Welder SG 120 A and included accessories.

This image displays the Gude Flux-Cored Welder SG 120 A unit, which is blue and black, featuring control knobs and switches on its front panel. Connected to the unit are a welding torch with its cable, a ground clamp, and a basic black welding mask. Also visible are a wire brush and spare contact tips, indicating the complete setup for flux-cored welding.

Isi ihe:

• Welding Unit: Main power source and control panel.
• Welding Torch: Delivers the flux-cored wire and welding current to the workpiece.
• Ala Clamp: Connects to the workpiece to complete the electrical circuit.
• Welding Mask: Provides eye and face protection from arc flash and sparks.
• Wire Brush: Used for cleaning welds.
• Contact Tips: Consumable parts for the welding torch.

4. Nhazi

1. Iwepu: Jiri nlezianya wepụ ihe niile dị na nkwakọ ngwaahịa. Nyochaa maka mmebi mbupu ọ bụla.
2. Njikọ ike: Connect the welder to a 230V, 50Hz power supply with a 16A circuit breaker. Ensure the power switch on the welder is in the "OFF" position before plugging it in.
3. Nwụnye waya:
   • Open the wire compartment.
   • Mount the flux-cored wire spool (up to 0.9 mm diameter) onto the spindle.
   • Feed the wire through the guide tube and into the drive rollers.
   • Adjust the drive roller tension to prevent slipping or crushing the wire.
   • Mechie ogige.
4. Torch and Ground Clamp Njikọ:
   • Ensure the welding torch is securely connected to the front panel of the welder.
   • Tinye ala clamp cable to the designated terminal on the welder.
5. Nkwadebe ihe eji arụ ọrụ: Clean the workpiece thoroughly to remove rust, paint, oil, or other contaminants that could affect weld quality.

5. Ọrụ

1. Ike Na: Switch the welder to the "ON" position.
2. Attach Ground Clamp: Securely attach the ground clamp gaa na ọrụ ahụ, na-eme ka ọ dị mma ịnweta kọntaktị eletriki.
3. Họrọ Ọkwa Ike: The SG 120 A offers two power levels: 60A and 90A. Select the appropriate level based on the material thickness.
   • For thinner materials (e.g., 1.5 mm), use the lower setting (60A).
   • For thicker materials (up to 5 mm), use the higher setting (90A).
4. Adjust Wire Feed Speed: Use the control knob to adjust the wire feed speed. Start with a moderate setting and adjust as needed to achieve a stable arc and good weld penetration.
5. ịgbado ọkụ:
   • Position the welding torch approximately 10-15 mm from the workpiece.
   • Press the trigger on the torch to initiate the arc and wire feed.
   • Maintain a consistent travel speed and torch angle to create a uniform weld bead.
   • Flux-cored welding produces slag, which will need to be removed after welding.
6. Nchekwa ekpo oke ọkụ: If the welder overheats, the thermal protection will activate, and the unit will temporarily shut down. Allow it to cool down before resuming operation.
7. Gbanyụọ: After welding, release the torch trigger, switch the welder to "OFF," and disconnect it from the power supply.

6. Nlekọta

Regular maintenance ensures the longevity and safe operation of your welder.

• Nhicha: Regularly clean the welding unit, especially the ventilation openings, to prevent dust and debris buildup. Use compressed air if available.
• Torch Maintenance:
  • Inspect the contact tip for wear and replace if necessary.
  • Ensure the nozzle is clean and free of spatter.
  • Check the torch cable for damage.
• Wire Drive System: Periodically check the wire drive rollers for wear and ensure they are clean.
• Ala Clamp: Gbaa mbọ hụ na ala clamp is clean and provides a secure connection.
• Nchekwa: Debe ihe mgbakwụnye ahụ n'ebe kpọrọ nkụ ma dị ọcha mgbe a naghị eji ya.

7. Nchọpụta nsogbu

8. Nka na ụzụ nkọwa

• Ụdị: Gude SG 120 A (Model Number: 20070)
• Ntinye Voltage: 230 V
• Ugboro: 50 Hz
• Max. Net Power: 3.2 kVA
• Net Protection: 16 A
• Enweghị Ibu Ibu Voltage: 31 V
• Ịgbado ọkụ Ugbu a: 60 A / 90 A (2 levels)
• Ọkpụrụkpụ ihe: 1.5-5 mm
• Max. Wire Diameter: 0.9 mm (flux-cored)
• Akụkụ ngwaahịa: 48.01 x 35.99 x 22 cm
• Arọ: 14 n'arọ

9. Akwụkwọ ikike na nkwado

For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.