Usoro ACMS12
Ọgbakọ
Nweta ndị njikwa ike
Ntuziaka nwụnye
ACMS12 Series Sub Assembly Access Power Controllers
Elsdị gụnyere:
ACMS12
– Iri na abụọ (12) ihe echekwabara fiusi
ACMS12CB
– Mpụta echekwabara PTC iri na abụọ (12).
gafereview:
Altronix ACMS12/ACMS12CB bụ obere ọgbakọ emebere ka ejiri na Altronix BC300, BC400, Trove1, Trove2 na Trove3 na nkeji ike kachasị. Ntinye ntinye abuo nke onye njikwa ike nweta na-enye ohere ka eduzi ya site na abụọ (2) nọọrọ onwe ha obere voltage 12 ma ọ bụ 24VDC Altronix ike na-enye mmadụ iri na abụọ (12) fiusi na-achịkwa onwe ya (ACMS12) ma ọ bụ PTC (ACMS12CB). A na-arụ ọrụ mmepụta site na sink na-emeghe oghere, na-emeghekarị (NO), na-emechi emechi (NC) ntinye ọkụ ọkụ ọkụ, ma ọ bụ mmepụta mmiri site na Access Control System, Card Reader, Keypad, Push Button, PIR, wdg ACMS12 (CB) ga-ebugharị ike na ngwaọrụ dị iche iche nke ịnweta njikwa ngwaike gụnyere Mag Locks, Electric Strikes, Magnetic Outpucu, etc. ụdịdị. Interface FACP na-enyere mgbapụ ihe mberede, nlekota mkpu, ma ọ bụ enwere ike iji kpalite ngwaọrụ inyeaka ndị ọzọ. A na-ahọrọ atụmatụ nkwụsị ọkụ ọkụ n'otu n'otu maka ihe ọ bụla ma ọ bụ niile nke iri na abụọ (12). Njikọ spade na-enye gị ohere ị nweta ike daisy yinye n'ọtụtụ ACMS12 (CB) modul. Njirimara a na-enye gị ohere ikesa ike n'elu ihe ndị ọzọ maka nnukwu usoro.
Nkọwapụta:
Ntinye Voltage:
- Ntinye 1: 12 ma ọ bụ 24VDC Altronix ike ọkọnọ.
- Ntinye 2: 12 ma ọ bụ 24VDC Altronix ike ọkọnọ ma ọ bụ 5 ma ọ bụ 12VDC sitere na VR6 Regulator.
- Ntinye ugbu a:
ACMS12: 20A ngụkọta
ACMS12CB: 16A ngụkọta. - Ntinye ihe mkpalite nwere ike họrọ nke iri na abụọ (12):
a) Ndenye na-emepekarị (NO) (kọntaktsị kpọrọ nkụ).
b) Ntinye nke emechiri emechi (NC) ( kọntaktị akọrọ).
c) Mepee ntinye sink onye nchịkọta.
d) Ntinye mmiri (5VDC – 24VDC) nwere ihe mgbochi 10K
e) Ngwakọta ọ bụla nke dị n'elu.
Nsonaazụ:
- ACMS12: Mwepụta echekwabara fuse @ 2.5A kwa mmepụta, enweghị oke ike.
Mkpokọta mmepụta 20A max.
Hụ Ntinye/Mpụta Voltage Ratings, pg. 7.
ACMS12CB: PTC echekwabara akara @ 2A kwa mmepụta, klaasị 2 nwere oke.
Mkpokọta mmepụta 16A max.
Agafela ọkwa ọkọnọ ike nke onye ọ bụla.
Hụ Ntinye/Mpụta Voltage Ratings, pg. 7.
Mkpokọta mmepụta ugbu a ekwesịghị ịfe oke. ogo dị ugbu a nke akụrụngwa ọkụ na-arụ ọrụ na ntinye ọ bụla.
Hụ mpụta kacha nke Altronix Ike. - Iri na abụọ (12) nke a na-achịkwa n'adabereghị na nsonaazụ ike Fail-Safe ma ọ bụ Fail-Secure.
- Enwere ike ịtọ nsonaazụ onye ọ bụla ka ọ bụrụ ọnọdụ gbanyụọ maka ije ozi (mpụta jumper setịpụrụ na ọnọdụ etiti).
- Enwere ike họrọ mmepụta iji soro ntinye ike 1 ma ọ bụ ntinye 2. mmepụta voltage nke ọ bụla mmepụta bụ otu ihe ntinye voltage nke ntinye ahọpụtara.
Hụ Ntinye/Mpụta Voltage Ratings, pg. 7. - Mbelata ịwa ahụ.
Kpupu oti mkpu ọkụ:
- Mwepu mkpu oku ọkụ (latching ma ọ bụ enweghị ike) bụ nhọrọ n'otu n'otu maka ihe ọ bụla ma ọ bụ niile nke iri na abụọ (12).
Nhọrọ ntinye mgbakwụnye ọkụ ọkụ:
a) Ọ na-emepekarị [NO] ma ọ bụ na-emechikarị [NC] ntinye kọntaktị akọrọ. Ntinye ngbanwe polarity sitere na sekit mgbama FACP. - Ntinye FACP WET bụ 5-30VDC 7mA.
- Ntinye FACP EOL chọrọ njedebe 10K nke resistor ahịrị.
- FACP mmepụta relay [NC]:
Ma FACP akọrọ mmepụta NC ma ọ bụ
Njikọ EOL dị n'ime na ACMS12(CB) na-esote.
Oke ACMS12 fuse:
- A na-atụ fiusi isi ntinye 15A/32V nke ọ bụla.
- A na-atụle fiusi mmepụta 3A/32V.
Ogo ACMS12CB PTC:
- Isi ntinye PTC bụ 9A nke ọ bụla.
- A na-edepụta PTC 2.5A.
Ihe ngosi LED:
- Igwe ọkụ na-acha anụnụ anụnụ na-egosi na agbanyere FACP.
- Onye voltage LED na-egosi 12VDC (Green) ma ọ bụ 24VDC (Red).
gburugburu:
- Ọnọdụ okpomọkụ na-arụ ọrụ: 0ºC ruo 49ºC ambient.
- iru mmiri: 20 ruo 93%, anaghị ekpo ọkụ.
Maka igwe:
- Akụkụ bọọdụ (W x L x H ihe ruru): 7.3" x 4.1" x 1.25" (185.4mm x 104.1mm x 31.8mm)
- Ibu ngwaahịa (ihe dị ka): 0.7 lb. (0.32 n'arọ).
- Ibu mbupu (ihe dị ka): 0.95 lb. (0.43 n'arọ).
Ntuziaka nwụnye:
Usoro wiwi ga-adị na koodu eletriki mba NFPA 70/NFPA 72/ ANSI / Canadian Electric Code / CAN/ULC-S524/ULC-S527/ULC-S537 yana koodu mpaghara na ndị ọchịchị nwere ikike. Ezubere ngwaahịa maka naanị ime ụlọ akọrọ.
Rụtụ aka na ntuziaka nwụnye nke obere ọgbakọ maka ịgbanye Mkpu. MS050913.
Jiri nlezianya review:
| Ikanam Nchọpụta | (pg. 5) | Eserese ngwa a na-ahụkarị | (pg. 6) |
| Tebụlụ njirimara njedebe | (pg. 5) | Eserese njikọ | (pg. 9-10) |
Nwụnye:
- Ugwu ACMS12/ACMS12CB n'ebe/nkpuchi achọrọ. Mgbe ị na-arịgo ACMS12/ACMS12CB naanị, jiri oghere nwanyị / nwanyị (nyere). Mgbe ị na-eji nhọrọ VR6 voltage regulator, jiri nwanyị / nwanyị spacers (nyere) n'etiti ACMS12/ACMS12CB na VR6 (Fig. 6, pg. 6).
Tinye ACMS12/ACMS12CB na spacers na-eji 5/16" pan isi skru (nyere).
Njikọ:
- Gbaa mbọ hụ na etinyere ndị jumpers niile [OUT1] - [OUT12] n'ọnọdụ gbanyụọ (etiti).
- Jikọọ obere voltage DC na-enye ike na ọdụ akara akara [+ PWR1 -], [+ PWR2 -]
- Tọọ mmepụta ọ bụla [OUT1] - [OUT12] ka ọ ga-esi na ike na-enye ike 1 ma ọ bụ 2 (Fig 1, pg. 3).
Mara: tụọ mmepụta voltage tupu jikọọ ngwaọrụ.
Nke a na-enyere aka izere mmebi nwere ike ime. - Gbanyụọ ọkụ tupu ị jikọọ ngwaọrụ.
Ọrụ:
Ihe dị mkpa: A na-ejikọta ihe ntinye / mmepụta na ihe ọkụ ọkụ ha (Fig 3, pg. 4). - Nhọrọ mmepụta: ACMS12 (CB) ga-enye ihe ruru iri na abụọ (12) ọkụ ọkụ.
Mbupute Ike agbanweela:
Jikọọ ntinye nke ngwaọrụ a na-akwado na njedebe akara [- Output1 +] site na [- Output12 +] na-elezi anya nke ọma.
• N'ihi na ọdịda-Safe ọrụ slide mmepụta akara mgbagha DIP mgba ọkụ akara [mmepụta] maka ndenye kwekọrọ ekwekọ n'ime ON ọnọdụ (Fig. 3, n'aka nri).
• N'ihi na ọdịda-Secure arụmọrụ slide mmepụta akara mgbagha DIP mgba ọkụ akara [mmepụta] maka ndenye kwekọrọ ekwekọ n'ime Gbanyụọ ọnọdụ (Fig. 3, n'aka nri). - Gbanye isi ọkụ mgbe ejikọrọ ngwaọrụ niile.
Ihe dị mkpa: A na-ejikọta ihe ntinye / mmepụta na ihe ọkụ ọkụ ha (Fig 3, pg. 4). - Nhọrọ ịkpalite ntinye:
Mara: Ọ bụrụ na ejighị nkwupụ mkpu ọkụ ọkụ, jikọọ resistor 10K Ohm na ọdụ ndị akara [GND na EOL], gbakwunyere jikọọ jumper na ọdụ akara akara [GND, RST].
Ntinye na-emepe emepe (MKWU):
Ngbanwe njikwa ihe ngbanwe slide nke akara DIP akara [NO-NC] maka ntinye kwekọrọ na ọnọdụ Gbanyụọ (Fig 4, n'aka nri). Jikọọ wires gị na njedebe akara [+ INP1 -] na [+ INP12 –].
Ntinye na-emechikarị (NC):
Ngbanwe njikwa ihe ngbanwe slide nke akara DIP akara [NO-NC] maka ntinye kwekọrọ na ọnọdụ ON (Fig 4, n'aka nri). Jikọọ waya gị na ọnụ ahịa akara [+ INP1 -] na [+ INP12 -].
Ntinye ihe nkwokọ mepere emepe:
Jikọọ ntinye sink onye na-anakọta oghere na ọnụ nke akara [+ INP1 -] na [+ INP12 -].
Mmiri (Voltage) Nhazi ntinye:
Jiri nlezianya na-ekiri polarity, jikọọ voltage ntinye wires na-akpalite wires na ihe mgbochi 10K ewepụtara na njedebe akara [+ INP1 -] na [+ INP12 -].
Ọ bụrụ na itinye voltage iji kpalite ntinye – tọọ mgbanwe INP Logic kwekọrọ na ọnọdụ “ON”.
Ọ bụrụ na iwepu voltage iji kpalite ntinye – tọọ mgbanwe INP Logic kwekọrọ na ọnọdụ “gbanyụọ”.
- Nhọrọ ihu mkpu ọkụ:
Ntinye [NC] emechiri emechi, nke na-emeghe [NO] ma ọ bụ ndenye ngbanwe polarity sitere na sekit mgbama FACP ga-akpalite nsonaazụ ahọpụtara.
Iji mee ka FACP kwupu maka mgbagha njikwa mmepụta slide
Mgbanwe DIP akara [FACP] maka mmepụta kwekọrọ na ON (Fig 5, n'aka nri).
Iji gbanyụọ FACP Kwupu maka mgbagha njikwa mmepụta mmịfe
Mgbanwe DIP akara [FACP] maka ngbanwe kwekọrọ ekwekọ (Fig 5, n'aka nri).
Ntinye na-emepe emepe:
Waya relay FACP gị na resistor 10K n'otu aka na ọdụ akara [GND] na [EOL].
Ntinye na-emechikarị:
Kwuo relay FACP gị na 10K resistor n'usoro nwere akara akara [GND] na [EOL].
Ihe mkpali ntinye sekit mgbama FACP:
Jikọọ ihe dị mma (+) na nke na-adịghị mma (-) site na mmepụta sekit mgbama FACP na njedebe akara [+ FACP -]. Jikọọ FACP EOL na njedebe akara [+ RET -] (a na-ezo aka na polarity na ọnọdụ mkpu).
Kpupu oti mkpu ọkụ na-adịghị egbochi:
Jikọọ jumper na njedebe akara [GND, RST].
Ịkwụsị njikọ Mkpuchi Mkpuchi Ọkụ:
Jikọọ ngbanwe nrụgharị nrụgharị NO na-emeghe na ọnụ nke akara [GND, RST]. - Mmepụta NC akọrọ FACP:
Mgbe daisy-chaining Fire mkpu mgbama n'etiti bọọdụ abụọ, jikọọ [NC & C] nke mbụ ACMS12(CB) na [GND & EOL] nke ọzọ ACMS12(CB). Tinye EOL jumper na ntụtụ etiti na ala.
Mgbe ị na-eji mmepụta a dị ka kọntaktị akọrọ NC na-etinye EOL jumper na etiti na ntụtụ elu.
Daisy Chaining Abụọ (2) ACMS12 (CB)
Ndị na-ahụ maka nnweta ike nke abụọ:
Jiri waya 18 AWG ma ọ bụ karịa UL edepụtara nke nwere 1/4” UL Aghọtara ọnụ ọnụ njikọ ngwa ngwa maka volta dị mma.tage/ugbu a maka njikọ jumper niile.
- Jikọọ akpa spade bọọdụ ACMS12(CB) nke akara [PWR1 +] na ọdụ bọọdụ ACMS12(CB) nke abụọ nke akara [+ PWR1].
- Jikọọ akpa ACMS12(CB) spade lug nke akara [COM –] na ọdụ ACMS12(CB) nke abụọ akara [PWR1 –].
- Jikọọ akpa spade bọọdụ ACMS12(CB) nke akara [PWR2 +] na ọdụ bọọdụ ACMS12(CB) nke abụọ nke akara [+ PWR2].
Ihe nchọpụta LED:
ACMS12 na ACMS12CB njikwa ike nnweta
| Ikanam | ON | Gbanyụọ |
| LED 1-Ikanam 12 (Uhie) | Mgbasa ozi (s) arụpụtaghị ike. | Mbupute relay (s) na-enye ike. |
| AKWKWỌ | Ntinye FACP kpalitere (ọnọdụ mkpu). | FACP nkịtị (ọnọdụ enweghị mkpu). |
| Mpụta akwụkwọ ndụ akwụkwọ ndụ 1-12 | 12VDC | – |
| Mpụta uhie 1-12 | 24VDC | – |
Tebụlụ njirimara njedebe:
ACMS12 na ACMS12CB njikwa ike nnweta
| Akụkọ Mgbe Ebighị Ebi | Ọrụ/Nkọwa |
| PWR1 - | 12 ma ọ bụ 24 VDC sitere na ọkụ ọkụ. |
| PWR2 - | 12 ma ọ bụ 24 VDC sitere na ọkụ ọkụ ma ọ bụ 5 ma ọ bụ 12 VDC sitere na VR6 regulator. |
| + INP1 - site na + INP12 — |
Iri na abụọ (12) na-achịkwa onwe ya nke ọma na-emepe emepe (NO), Emechiri emechi (NC), Open Collector Sink ma ọ bụ ihe ntinye mmiri mmiri. |
| C, NC | Mmepụta FACP Dry NC ma ọ bụ njikọ EOL dị n'ime na ACMS12(CB) na-esote. |
| GND, RST | FACP interface latching ma ọ bụ enweghị latching. Enweghị ntinye akọrọ. Klas 2 nwere oke ike. A ga-eme ka ọ dị mkpụmkpụ maka interface FACP na-adịghị ejide ma ọ bụ Ntọgharị FACP Latch. |
| GND, EOL | Ọnụ ntinye ntinye FACP na-elekọta EOL maka ọrụ FACP ngbanwe polarity. Klas 2 nwere oke ike. |
| — F, + F, — R, + R | Ihe nrịbama FACP na ntinye sekit na nkwụghachi azụ. Klas 2 nwere oke ike. |
| - Mpụta 1 + gafere - Mpụta 12 + |
Mpụta iri na abụọ (12) nke a na-achịkwa nke onwe ya (Fail-Safe or Fail-Secure). |
Eserese ngwa a na-ahụkarị:
Ntinye/Mpụta Voltage Ratings
| Ntinye Voltage na Isi Iyi | Mmepụta Voltage Ntụle |
| 5VDC (site na VR6 regulator) | 5VDC |
| 12V (nke sitere na VR6 regulator) | 12VDC |
| 12VDC (site na mpụga ike ọkọnọ) | 11.7-12VDC |
| 24VDC (site na mpụga ike ọkọnọ) | 23.7-24VDC |
Nsonaazụ kacha elu nke Altronix Ike:
| Edepụtara UL ma ọ bụ Nweta ike | Mmepụta Voltage Ntọala | Oke. Mmepụta ugbu a |
| AL400ULXB2 / eFlow4NB | 12VDC ma ọ bụ 24VDC | 4A |
| AL600ULXB / eFlow6NB | 12VDC ma ọ bụ 24VDC | 6A |
| AL1012ULXB / eFlow102NB | 12VDC | 10A |
| AL1024ULXB2 / eFlow104NB | 24VDC | 10A |
| VR6 | 5VDC ma ọ bụ 12VDC | 6A |
VR6 - Voltage Onye nchịkwa
gafereview:
VR6 voltage regulator na-atụgharị ntinye 24VDC ka ọ bụrụ mmepụta 5VDC ma ọ bụ 12VDC ahaziri. Emebere ya ka ọ rụọ ọrụ na ACMS12(CB) site n'ikwe ka ịkwanye njikwa ike nnweta ozugbo n'elu VR6 iji chekwaa oghere mkpuchi na ime ka njikọ dị mfe. Tụtụ aka na ntuziaka nwụnye VR6 Mkpu. 050517.
Nkọwapụta:
Ntinye ike/mpụta:
- Ntinye: 24VDC @ 1.75A - Mmepụta: 5VDC @ 6A.
- Ntinye: 24VDC @ 3.5A - Mmepụta: 12VDC @ 6A.
Mpụta:
- 5VDC ma ọ bụ 12VDC ahaziri mmepụta.
- Oke mmepụta 6A max.
- Mbelata ịwa ahụ.
Ihe ngosi LED:
- Ntinye na mmepụta LEDs.
Eletriki:
- Ọnọdụ okpomọkụ na-arụ ọrụ: 0ºC ruo 49ºC ambient.
- iru mmiri: 20 ruo 93%, anaghị ekpo ọkụ.
Maka igwe:
- Ibu ngwaahịa (ihe dị ka): 0.4 lb. (0.18 n'arọ).
- Ibu mbupu (ihe dị ka): 0.5 lb. (0.23 n'arọ).
Jikọọ ACMS12(CB) na VR6:
- Kechie oghere nwoke/nwanyị (nke enyere) na pems dabara na ụkpụrụ oghere maka VR6 na ebe/mkpọchi achọrọ. Jiri igwe oghere maka oghere mgbago nwere ụkpụrụ kpakpando (Fig 7a, pg. 8).
- Nkwụnye nwoke 8-pin njikọ na nwanyị 8-pin nkwụnye na VR6 osisi (Fig. 7, pg. 8).
- Kechie oghere nwanyị / nwanyị na oghere nke nwoke / nwanyị (Fig 7, pg. 8).
Jiri igwe oghere n'elu rịgoro oghere nwere ụkpụrụ kpakpando (Fig. 7a, pg. 8). - Kpọkọtanụ 8-pin nwoke njikọ na ebe nwanyị nke ACMS12/ACMS12CB, wee tinye osisi na spacers tinye n'ọrụ nyere 5/16" pan isi kposara (Fig. 7, pg. 8).
- Jikọọ ọkụ ọkụ 24VDC na ọdụ akara akara [+ PWR1 -] nke ACMS12/ACMS12CB (Fig. 8, pg. 7).
- Họrọ mmepụta voltage 5VDC ma ọ bụ 12VDC iji mgba ọkụ [S1] na VR6.
- Nzọụkwụ 4-10 zuru ezu (pgs 3-4).
Eserese Nkọ:
Ihe osise 8 - Daisy-chaining otu ma ọ bụ karịa ACMS12 nkeji.
Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Na-adịghị latching.
Ihe osise 9 - Daisy-chaining otu ma ọ bụ karịa ACMS12 nkeji.
Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Ntọgharị Single.
Ihe osise 10 - Daisy chaining otu ma ọ bụ karịa ACMS12 nkeji.
Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Ntọgharị n'otu n'otu.
Ihe osise 10 - Ntinye ngbanwe polarity sitere na mmepụta sekit mgbaàmà FACP (a na-ezo aka na polarity na ọnọdụ mkpu).
Na-adịghị latching.
Ihe osise 11 - Ntinye ngbanwe polarity sitere na mmepụta sekit mgbaàmà FACP (a na-ezo aka na polarity na ọnọdụ mkpu).
Latching.
Ihe osise 12 – Ntinye mkpanaaka emechiri emechi
(Na-adịghị egbu egbu).
Ihe osise 13 – Ntinye mkpanaaka emechiri emechi
(Latching).
Ihe osise 14 – Mepee ntinye mkpanaaka
(Na-adịghị egbu egbu).
Ihe osise 15 – Mepee ntinye mkpanaaka
(Latching).
ndetu:-
Altronix abụghị maka mmejọ ederede ọ bụla.
140 58th Street, Brooklyn, New York 11220 USA
ekwentị: 718-567-8181
faksị: 718-567-9056
websaịtị: www.altronix.com
ozi-e: info@altronix.com
Akwụkwọ ikike ndụ
IIACMS12/ACMS12CB I01V
ACMS12/CB Ntuziaka nwụnye nke obere ọgbakọ
Akwụkwọ / akụrụngwa
 |
Altronix ACMS12 Series Sub Assembly Access Power Controllers [pdf] Ntuziaka nwụnye ACMS12, ACMS12CB, ACMS12 Series Sub Assembly Access Power Controllers, Sub Assembly Access Power Controllers, Access Power Controllers, Power Controllers |