Akwụkwọ ntuziaka onye ọrụ PixLite 16 ogologo ogologo Mk2
Akụrụngwa Mkpu 1.0 - 1.1

Okwu mmalite

This is the user manual for the PixLite 16 Long Range Mk2 pixel controller , hardware version 1.0 – 1.1.
The PixLite 16 Long Range Mk2 controllers convert E1.31 (sACN) or Art-Net protocols from a lighting console, media server or computer lighting software into various pixel LED protocols.
This controller is designed to overcome distance problems typically encountered when running many pixels from a single location. The PixLite 16 Long Range Mk2 sends differential data signals directly out of the controller which can be transmitted reliably using any standard network cable at distances in excess of 300m (1000’). At the receiver end, the differential signals are then converted back to signals suitable for pixels. This system allows the user to distribute a large number of pixels from a centralized pixel controller easily, without needing to worry about the typical signal degradation problems.
PixLite 16 Long Range Mk2 na-egosipụta ikike mmepụta nke ruru 96 eluigwe na ala nke multicast/unicast E1.31 ma ọ bụ Art-Net data. Nke a, jikọtara ya na sọftụwia nhazi atụmatụ dị elu yana mfe iji mee ihe, na-eme PixLite 16 Long Range Mk2 bụrụ nhọrọ magburu onwe ya maka ngwa ọkụ pixel gị.
This manual covers physical aspects of the PixLite 16 Long Range Mk2 controller and its essential setup steps only. Detailed information about its configuration options can be found in the ‘PixLite Configuration Guide’. Other manuals and the PixLite Configuration Guide may be downloaded from here: www.advateklighting.com/downloads

Ndetu nchekwa

A na-ebufe bọọdụ ahụ n'ime akpa mgbochi static ma nwee ọtụtụ ihe ndị nwere mmetụta elektrọn na ya. Ekwesịrị ịhụ usoro mgbochi static dabara adaba mgbe ị na-ejikwa bọọdụ ahụ. Maka examplee, ịkwesighi ịnọdụ ala njikwa na kapeeti, ma ị ga-ezere imetụ ihe ndị dị na njikwa ahụ aka na-enweghị isi.

Nwụnye

4.1 - Ike inye
Power to the controller is applied via the power bank screw terminal connector, located on the lefthand edge of the board, as shown in Figure 1 below. It is clearly marked on the PCB with its polarity.
Likewise, power to the receiver board is applied via the large screw terminal connector on the left hand edge of the board labelled ‘Power In’. It is also clearly marked with polarity.
Igwe njikwa ihe na-ebugharị PixLite 16 Ogologo ogologo Mk2 chọrọ voltage nke n'etiti 5V-24Vdc na ntinye ntinye kachasị nke 1.5A @ 5V.
Ihe nnata ogologo ogologo bụ bọọdụ na-enye ọkụ ọkụ ma si otú a na-achọ ọkụ kwesịrị ekwesị. Voltage to the power input is recommended to be between 5V and 12Vdc . The receiver will operate up to 24Vdc, however attention should be paid to cooling the controller when operating above 12V.
Mara: Ọ bụ ọrụ onye ọrụ ịhụ na ọkụ ọkụ ejiri dabara voltage nke pikselụ fixture ha na-eji na na ọ nwere ike na-enye ezi ego nke ike/ugbu a.
Ngụkọta kacha ugbu a site na nnata bụ 15A.

4.2 - Fuses mmepụta nke nnata
A na-echekwa mpụta nke ọ bụla site na fiusi obere agụba. Onye nnata PixLite 16 Long Range Mk2 na-abịa na fuses 7.5A na ndabara. Ị nwere ike iji uru ọ bụla nke fuse, ruo yana gụnyere 7.5A, dabere na ngwa gị akọwapụtara. Nsonaazụ nke onye ọ bụla ekwesịghị ịfe 7.5A na mkpokọta ugbu a ekwesịghị gafere 15A.
4.3 - Ike mgbagha na-ebufe
A na-ahazi ike mgbagha na-akpaghị aka site na ntinye ike. Naanị jikọọ ọkụ eletrik gị nke dị n'etiti 5V na 24Vdc na ọdụ ọkụ skru. A na-echekwa sekit mgbakasị ahụ site na fiusi mini agụba 2A.
4.4 - Njikwa data
Ejikọrọ data Ethernet site na eriri netwọk ọkọlọtọ n'ime jakị RJ45 Ethernet dị n'akụkụ aka ekpe nke unit ahụ. Onye njikwa na-akwado Streaming ACN (sACN / E1.31) ma ọ bụ data Art-Net.
4.5 - Mpụta data
The receiver board outputs (RJ45 jacks) are located along the bottom edge of the control board.
There are 8 in total – each one containing 4 differential pairs. The pin-out of the RJ45 jack is shown below. It is not important to understand this diagram for most users, you simply use a standard network cable to connect the transmitter and receiver boards.

4.6 - Ijikọ nnyefe na ndị nnata
4.6.1 - Njikọ njikọ
Receivers are connected to the transmitter via the RJ45 jacks along the bottom edge of the control board. Each jack is labelled with its output number 1-8. These ports are not network ports, and should not be connected to any networking equipment. They are specifically designed to connect a PixLite transmitter with a PixLite receiver. For this reason, the standard network cable you use can be safely used in excess of 300m.
A na-egosi nhazi nke ọma na foto 3 dị n'okpuru ebe a, nke na-egosikwa ole pikselụ enwere ike ịgbapụ na mmepụta nke ọ bụla.

4.7 - Jikọọ Pixel LEDs
A na-ejikọta ọkụ pikselụ ozugbo site na njikọ screw 2 pluggable na ndị nnata. A na-akpọ njikọ ọ bụla na nọmba ọwa mmepụta ya (1-2) yana pin 1 ka edokwara nke ọma. Naanị waya ọkụ gị n'ime ọdụ ụgbọ mmiri ọ bụla wee tinye ha n'ime oghere mating.
Ịdọ aka ná ntị: It is very important not to short +ve ont o the clock or data lines when using pixels greater than 5V. Note that this can also happen from poor waterproofing when rain shorts the higher voltage na nke ọ bụla n'ime wires ndị ahụ na pikselụ/wiring gị.
Ogologo eriri USB n'etiti mmepụta na pikselụ mbụ ekwesịghị ịfe 15m.
Ọgụgụ 4 na-egosi pin-apụ nke njikọ mmepụta pixel.

4.8 - Ụdị ịgbasawanye
If your pixels only use a single data line, you may optionally activate expanded mode on the controller. If using the PixLite 16 Long Range Mk2 with a PixLite T16X-S Mk3, expanded mode must be used, meaning that pixels can only use a single data line. The clock pins are not connected, as per the pintout below. In expanded mode, the clock signals are re-purposed for data signals instead. This means the controller effectively has twice as many pixel outputs (32), but half as many pixels per output can be run.
Ọnọdụ ịgbasawanye nwere ike inye aka mee ka mgbanwe dị na sistemu dị ka enwere mpụta karịa. Ọ nwekwara ike inye aka site n'ịgbasa ọnụọgụ pikselụ a na-achịkwa n'ofe nsonaazụ ndị ọzọ, nke nwere ike inye aka nweta ọnụego ume ọhụrụ dị elu ma ọ bụrụ na ejighị pikselụ emechiri emechi.
E gosipụtara pinout maka ọnọdụ ịgbasawanye na foto 5 dị n'okpuru.

Nhazi netwọkụ

5.1 - Nhazi netwọkụ

Figure 6 shows a typical network topology for the PixLite 16 Long Range Mk2 controller(s) LAN.
Nrụnye na-eji multicast sACN ga-erite uru site na iji IGMP Snooping akụrụngwa netwọk nyere aka mgbe enwere ọtụtụ mbara igwe multicast na netwọk karịa nke ọ bụla PixLite na-eji. Ọ bụrụ na e nwere karịa 96 eluigwe na ụwa nke multicast sACN na netwọk mgbe ahụ IGMP Snooping bụ iwu.
Inwe rawụta na netwọk abụghị iwu na ọ bara uru maka njikwa adreesị IP yana DHCP (lee ngalaba 5.2.1). Mgbe IGMP snooping, a nwekwara ike ịchọ onye rawụta (dabere na ọrụ mgba ọkụ netwọk gị).

N'ime otu nrụnye njikwa, ọ nwere ike ịka mma ijikọ onye njikwa ozugbo na igwe nnabata, dị ka egosiri na Figure 7. Achọghị eriri crossover na nke a, mana enwere ike iji ya ma ọ bụrụ na achọrọ ya.
Enwere ike itinye njikwa (s) ozugbo n'ime LAN ọ bụla dịbu adị dị ka mgbasa ozi gị, ụlọ ma ọ bụ netwọk ụlọ ọrụ gị, a na-enye eserese ndị a dị n'elu dị ka mbụ.amples.

5.2 - adreesị IP
5.2.1 - Iji rawụta
Ndị na-anya ụgbọ ala nwere ihe nkesa DHCP n'ime ha - nke a pụtara na ha ga-agwa ngwaọrụ etinyere n'ime ha ihe adreesị IP ha ga-eji, ma ọ bụrụ na a jụọ ya.
A na-eme DHCP na ndabara mgbe niile na onye njikwa PixLite ka ọ nwee ike jikọọ ozugbo na netwọkụ ọ bụla dị na ya na rawụta. Agbanyeghị, ị nwere ike ịhọrọ inye adreesị IP kwụ ọtọ ozugbo emebere nkwukọrịta site na enyemaka Advatek. Ọ bụrụ na onye njikwa ahụ nọ na ọnọdụ DHCP ma onye nkesa DHCP enyeghị ya adreesị IP, ọ ga-apụ n'oge obere oge (ihe dị ka sekọnd 30) yana ndabara na IP static nke '192.168.0.50'.
Ọ bụrụ na agbanyere ọnọdụ DHCP, ma ọkwa na ike LED ga-agbanye ọnụ ruo mgbe onye njikwa na-anata adreesị IP ma ọ bụ oge na IP nke ndabara. Mgbe nke a gasịrị, ọkụ ọkụ ọkụ ga-anọgide na-esi ike na ọnọdụ LED ga-egbuke egbuke, na-egosi na ọ nọ na-agba ọsọ mode na njikere maka ojiji.
Ọ bụrụ na e kenyere onye njikwa adreesị IP static, mgbe ahụ ọkụ LED ga-esi ike site na ike elu.

5.2.2 - Iji mgba ọkụ / Direct
Ọ nwere ike ịdị mkpa ijikọ njikwa na netwọk na-enweghị ihe nkesa DHCP ma ọ bụ ọbụna ozugbo na igwe nnabata kama iji rawụta. N'okwu a (maka nhazi oge mbụ) ị ga-achọ ijide n'aka na etinyere ihe nkwụnye netwọkụ nke kọmputa gị na mpaghara IP nke onye njikwa ahụ ga-adabara na (mmebi njikwa na 192.168.0.50). Nke a pụtara na PC gị IP kwesịrị ịbụ 192.168.0.xxx ebe xxx bụ ihe ọ bụla n'etiti 1 na 254, ọzọ karịa 50. The subnet nkpuchi na PC gị kwesịrị ịtọ 255.255.255.0.
Mara: Akụrụngwa Advatek Assistant ga-achọpụta na akpaghị aka ma ọ bụrụ na ejikọrọ onye njikwa na netwọkụ ahụ, ọbụlagodi na ọ nọ na mpụga adreesị IP nke nkwụnye ahụ. Ọ ga-akpali gị ịgbanwe ntọala IP ma ọ bụrụ na achọpụtara ọnọdụ a.
Ozugbo ị nwere ike ịchọpụta onye njikwa na nke ọma na Advatek Assistant, anyị tụrụ aro ka ịtọ onye njikwa ahụ na adreesị IP kwụ ọtọ na-abụghị nke ndabara.
Ọgụgụ 8 na-egosi nseta ihuenyo nke ntọala netwọkụ kọmputa a na-ahụkarị iji kpakọrịta PixLite 16 Long Range Mk2 njikwa na nke mbụ na-enweghị rawụta.

5.2.3 – Forcing the Default IP Address
Ọ bụrụ na ị chefuo IP nke onye njikwa ma ị nweghị ike ịhụ ya na Advatek Assistant, enwere ike ịmanye ya na IP ndabara. Enwere ike iji usoro dị mfe mee ihe na mgbake ọkụ:

1. Jide bọtịnụ “Factory IP” na PCB wee welie njikwa njikwa
2. Mgbe sekọnd ole na ole hapụ bọtịnụ ahụ. Adreesị IP onye njikwa ga-abụ 192.168.0.50.

Ị ga-enwe ike ugbu a ịtọ ntọala netwọk PC gị ka ịchọta onye njikwa na IP a wee gbanwee ntọala IP ka ọ bụrụ adreesị IP static masịrị.

Ọrụ

6.1 - Mmalite
Mgbe itinye ike, onye njikwa ga-amalite ngwa ngwa wepụta data na ndị nnata, na-enye iwu ka pikselụ gbanyụọ. Ọ bụrụ na ezigaghị data na njikwa, pikselụ ga-anọgide na-agbanyụ ruo mgbe enwetara data bara uru. N'oge a na-arụ ọrụ nkịtị, na njikwa ọkụ ọkụ ndụ ndụ ga-anọgide na-adị ike na ọkwa uhie LED ga-egbuke egbuke iji gosi onye njikwa na-agba ọsọ ma na-emepụta data Ethernet ọ bụla natara na ndị nnata.

6.2 - Izipu data
A na-eziga data ntinye site na PC / ihe nkesa / njikwa ọkụ na njikwa site na Ethernet site na iji "DMX n'elu IP" protocol dị ka sACN (E1.31) ma ọ bụ Art-Net.
Ọ bụrụ na enwetaghị data mbata maka sekọnd ole na ole, pikselụ ga-agbanyụ na-akpaghị aka ma ọ bụrụ na agbanyụrụ nhọrọ ahụ na nhazi gị. Ọ bụrụ na anaghị ejikwa pikselụ ahụ, hụ na ị họrọla ụdị pikselụ IC ziri ezi na Advatek Assistant n'okpuru taabụ 'LED'.

6.3 - Mmepụta
6.3.1 - Mmepụta Pixel
Nke ọ bụla n'ime jakị mmepụta RJ8 njikwa 45 nwere ike ịnya data ruru 12 eluigwe na ala. Nke a na-enye ohere ka a chụpụ ngụkọta nke eluigwe na ụwa 96 n'otu njikwa (na mgbakwunye na 4 DMX512 Universe mmepụta).
Ọnụego ume ọhụrụ nke pikselụ ga-adabere n'ụdị mgbawa pixel arụ ọrụ.
Higher speed pixels will result in higher refresh rates. Pixels with no clock line will have a relatively low refresh rate when a significant number of pixels are used on a single output. Advatek recommends the use of clocked pixels whenever using a large number of sequential pixels on any output. Typically, the refresh rate can vary from 20 fps at the low end on data only pixels and up to 100+ fps at the higher end.

6.3.2 - DMX512 mmepụta
The PixLite 16 Long Range Mk2 provides 4 DMX512 output s which can be accessed either by pluggable screw terminal connectors or by RJ45 jacks. The hardware layer on which the DMX512 protocol operates is the RS485 electrical  communications standard. This is a differential transmission system consisting of a two-wire differential signal pair and a ground connection.
Ideally the differential signals should be wired into a twisted pair cable. The D+, D- and ground connections are clearly labelled on the PCB for the screw terminal connectors.
Mwepụta ndị a na-arụ ọrụ dị ka ihe mmepụta mbara igwe DMX512 n'otu n'otu, na-enye onye ọrụ nke ọma na akwa E1.31 ma ọ bụ Art-Net ruo 4 x DMX512 (na mgbakwunye na mmepụta pixel nkịtị).
A na-ejikọkwa data mgbaama DMX512 site na oghere RJ45 anọ kwụ ọtọ. Njikọ jumper na bọọdụ (nke gbara okirikiri na eserese 9 dị n'okpuru) na-enye ohere mmepụta RJ45 DMX ọ bụla iji ma ọ bụ wiring 'ESTA' ma ọ bụ nhazi wiring 'LOR'. (A na-ebufe ndị njikwa niile na njikọ dị na nhazi 'ESTA'.)
Mara: Mpụta DMX anọghị na ọkụ eletrik.
Njikọ ndị a niile na njikọ jumper dị na nsọtụ aka nri nke njikwa dịka egosiri na foto 9 dị n'okpuru.

N'okpuru bụ pin-out RJ45 maka njikọ DMX mgbe ahọpụtara wiwi "ESTA":

N'okpuru bụ pin-out RJ45 maka njikọ DMX mgbe ahọpụtara wiwi "LOR":

6.3.3 - Mmepụta Fans
Onye na-ahụ maka njikwa na-egosipụta mmepụta fan inyeaka nke nwere ike ịgbanye onye na-efe efe (s) nke mpụga maka ime ka ogige ahụ dị jụụ nke etinyere na njikwa ahụ, dị ka egosiri na foto 12 dị n'okpuru. Njirimara a bara uru iji mee ka ọnọdụ okpomọkụ na-achịkwa mgbe ị na-ebuli njikwa na nnukwu wattage ike ọkọnọ ọnụ na a obere, ohere gbochiri.

Mmepụta voltage nke mmepụta fan bụ otu ihe ntinye voltage. Yabụ, iji gbaa onye ofufe 12V maka example, ị ga-achọ iji ntinye ntinye 12V voltage. Ihe mmepụta fan nwere ike ịnye ihe ruru 15W nke ike mmepụta na-aga n'ihu ma na-achịkwa PWM. A na-echekwa mmepụta ya site na fuse mini-blade 3A.
Ọrụ bụ isi bụ nke a: Na Advatek Assistant, onye ọrụ nwere ike ịtọ ọnọdụ okpomọkụ nke mkpuchi ahụ agaghị agafe. Onye na-ahụ maka ya ga-emezigharị ọsọ fan na-akpaghị aka dabere na ọnọdụ okpomọkụ dị ugbu a dịka ihe mmetụta okpomọkụ nke onye na-ahụ maka nọ n'elu osisi tụrụ.
Maka exampYabụ, ọ bụrụ na etinyere ọnọdụ okpomọkụ na 30 Celsius, mgbe ahụ tupu oge okpomọkụ ahụ, onye na-ahụ maka ya ga-agbanye fan ahụ wee jiri nwayọọ nwayọọ gbanye.amp gbalie ọsọ ruo mgbe ọ ruru 100% ma ọ bụrụ na achọrọ ya, n'ịgbalị ịnọgide na-enwe okpomọkụ ma ọ bụ n'okpuru 30 Celsius. Ọ bụrụ na ọnọdụ okpomọkụ na-ebelata, fan ga-akwụsịlata. Onye njikwa ga-anwa idobe ọnọdụ okpomọkụ n'okpuru ebe a tọhapụrụ. Ọ bụrụ na ọnọdụ okpomọkụ ahụ achọpụtara ruru ogo a na-ahazi, mmepụta fan ga-adị 100% n'oge a.

6.4 – Usoro Nleba ngwaike
The controller features a built- in test pattern to assist in troubleshooting during an installation. To put the controller into this mode, press and hold the ‘Factory IP’ button for 3 seconds (after the controller is already running) or turn it on remotely from the “Test” tab in the Advatek Assistant.
The controller will then enter the test pattern mode, where different test patterns are available as described in the table below. The pattern will display the test pattern on all pixels on each of the pixel outputs and any enabled DMX512  outputs simultaneously . Pressing the ‘ Factory IP ‘ button while in test mode will move through each of the patterns successively in one continuous loop.

Nwalee	Ọrụ
	Nsonaazụ ga-agbagharị na-akpaghị aka site na agba uhie, akwụkwọ ndụ akwụkwọ ndụ, acha anụnụ anụnụ na ọcha n'oge etiti oge. Pịa bọtịnụ na-aga na ọnọdụ ọzọ.
	Uhie siri ike
	Green siri ike
	Blue siri ike
	Ọcha siri ike
	Outputs will slowly move through a full continuous colour fade. Pressing the button will loop back to the original colour cycle test mode.

Ka ịpụ na ọnọdụ ule pịa ma jide bọtịnụ 'Factory IP' ala ọzọ maka sekọnd 3 wee hapụ ya.
The hardware test requires that the pixel driver chip type and number of pixels per output are set correctly in the Advatek Assistant . In this way you can test if that part of your configuration is correct and isolate other possible problems with the incoming Ethernet data side.

Firmware mmelite

Onye njikwa ahụ nwere ike imelite ngwa ngwa ya (software ọhụrụ). A na-emelitekarị iji dozie nsogbu ma ọ bụ ịgbakwunye atụmatụ ọhụrụ.
Iji mee mmelite firmware, hụ na ị nwere PixLite 16 Long Range Mk2 njikwa jikọọ na netwọk LAN dị ka akụkụ 5.1.
Firmware ọhụrụ dị na Advatek website na njikọ dị n'okpuru: www.advateklighting.com/downloads
Ihe ebudatara file a ga-edobe n'ụdị ".zip", nke a ga-ewepụta. The "hex" file bụ nke file nke onye njikwa chọrọ.

7.1 - Ime nkwalite ọkọlọtọ

1. Mepee ihe enyemaka Advatek. Pịa “Search” ozugbo onye njikwa chọrọ pụtara na mpio isi, pịa ya ugboro abụọ.
2. Window nhazi ga-apụta. Pịa taabụ "Misc" wee chọta bọtịnụ "Nwelite Firmware" wee pịa ya. Window “mmelite firmware” ga-apụta, dị ka egosiri na foto 13 dị n'okpuru. Pịa "nchọgharị" ka ịchọta ngwa ngwa file ị chọrọ iji.
3. Pịa na bọtịnụ "mmelite".
4. Ozugbo mmelite ahụ zuru, igbe ozi ga-apụta na-ekwu na ọ dechara nke ọma.
5. Onye njikwa ahụ ga-amaliteghachi onwe ya na-akpaghị aka wee malite ịme ngwa ngwa ngwa ngwa ọhụrụ ozugbo.

Ọ bụrụ na enwere ihe na-adịghị mma na firmware emelitere, megharịa usoro ahụ ọzọ ma ọ bụrụ na ọ ka na-ahụ anya na nhazi nhazi. Ma ọ bụghị ya, rụtụ aka na nchọpụta nsogbu na ngalaba 9 maka ozi ndị ọzọ.

7.2 - Na-eme mmelite firmware mgbake
N'oge a na-adịghị ahụkebe nke onye njikwa ahụ zutere njehie na firmware ya, enwere ike ịme mmelite firmware mgbake. Nke a nwere ike ịdị mkpa ma ọ bụrụ na usoro mmelite firmware dị na Nkebi 7.1 dara.

1. Gbadaa njikwa ahụ wee jide bọtịnụ "Bootloader".
2. Tinye ike. Ọkwa na ike LED kwesịrị ịdị na-egbuke egbuke ọzọ iji gosi na onye njikwa nọ na ọnọdụ bootloader. Ọ dịla njikere ugbu a maka mmelite firmware.
   Onye njikwa ahụ ga-adaba na adreesị IP nke 192.168.0.50 na ọnọdụ a, yabụ ị ga-ahụrịrị na PC gị na-eme mgbake dị na netwọkụ dị n'otu adreesị dị ka adreesị IP a (dịka 192.168.0.10).
3. Iji Advatek Assistant, pịa ọchụchọ na isi mpio ma ị ga-ahụ onye njikwa na-egosi na "Bootloader" na kọlụm firmware. Ịpị ya ugboro abụọ ga-ebulite ya file chọgharịa windo dị ka egosiri na foto 13 dị n'elu.
4. Pịa chọgharịa ka ịchọta ngwa ngwa file.
5. Pịa bọtịnụ mmelite. Mmelite ahụ ga-ewe naanị sekọnd 5, igbe ozi ga-apụta ozugbo emechara mmelite ahụ.
6. Onye njikwa kwesịrị iji firmware ọhụrụ na-arụ ọrụ ugbu a.

Nkọwapụta

8.1 - Nkọwa ọrụ
Tebụlụ dị n'okpuru na-akọwapụta ọnọdụ ọrụ akwadoro maka onye njikwa PixLite 16 Long Range Mk2.

Oke	Uru/ Oke	Nkeji
Ntinye mbufe Voltage Oke	5-24	V DC
Recommended Receiver Voltage Oke	5-12	V DC
Absolute Max Receiver Voltage1	24	V DC
Max Current Per Receiver	15	A
Oriri oke Logic ugbu a @ 5V	1200	mA
Ike kacha mma nke Fans	15	W
Recommended Ambient Temperature2	-20 ruo +50	Celsius C
Okpomọkụ zuru oke nke akụrụngwa PCB	-40 ruo +80	Celsius C
Maximum Current Per Receiver Pixel Output	7.5	A

1. Active cooling is highly recommended.
2. Naanị oke akwadoro, okpomoku akụrụngwa ga-edoberịrị n'ogo kacha elu ha. Eji Advatek Assistant software nyochaa okpomọkụ akụrụngwa ka akwadoro.

8.2 - Nkọwapụta igwe
E gosipụtara bọọdụ njikwa (Njirimara 14) na bọọdụ nnabata (Njirimara 15) akụkụ na ebe niile na-ebuli oghere n'okpuru.

Nchọpụta nsogbu

N'ozuzu, nchọpụta nsogbu chọrọ ilele LEDs na bọọdụ njikwa.
9.1 - Koodu LED
Biko rụtụ aka na tebụl dị n'okpuru maka koodu ọnọdụ maka ọnọdụ onboard na LEDs ike.

Status LED (Red)	Power LED (Green)	Ọnọdụ
Na-egbuke egbuke	siri ike	Arụmọrụ nkịtị, Main ngwa na-aga nke ọma
Na-egbuke egbuke nwayọọ	siri ike	Ule ule na-agba ọsọ
Na-egbuke egbuke ọnụ	Na-egbuke egbuke ọnụ	Looking for IP address (DHCP Mode)
siri ike	siri ike	Ngwa ngwa anaghị arụ ọrụ
Gbanyụọ	siri ike	Ngwa ngwa anaghị arụ ọrụ
siri ike	Gbanyụọ	Ngwa ngwa anaghị arụ ọrụ
Na-egbuke egbuke ọzọ	Na-egbuke egbuke ọzọ	Ụdị bootloader
Gbanyụọ	Gbanyụọ	Enweghị ike

Biko rụtụ aka na tebụl dị n'okpuru maka koodu ọnọdụ maka LEDs ọnọdụ jakị Ethernet.

Njikọ LED (Green)	LED data (Yellow)	Ọnọdụ
siri ike	Na-egbuke egbuke	Ejikọtara ọ dị mma, na-anata data
siri ike	Gbanyụọ	Ejikọtara nke ọma, enweghị data
Gbanyụọ	Gbanyụọ	Enweghị njikọ etinyere

9.2 - Enweghị ọkụ ọkụ / ọnọdụ
Gbaa mbọ hụ na ọkụ gị na-enye voltaji ziri ezitage as per Section 4.1. Additionally, ensure that it can supply enough current to drive the lights that are connected. You should also try disconnecting the pixel output s and see if the controller then turns on. If the supplied power is correct, try performing a recovery firmware update as per Section 7.2.
9.3 - Enweghị njikwa pixel
Lelee na ahaziri ụdị pikselụ IC ziri ezi. Lelee wiwi anụ ahụ na pinout nke pikselụ, yana fuses mmepụta na nnata.
9.4 - Okwu ndị ọzọ
Lelee koodu LED dị ka akụkụ 9.1. Ọ bụrụ na ngwaọrụ ahụ ka na-emezughị dị ka a tụrụ anya ya, rụgharịa nrụpụta nrụpụta ụlọ nrụpụta na ngwaọrụ dị ka ngalaba 9.5 dị n'okpuru. Maka ozi kachasị ọhụrụ, yana ndụmọdụ ụlọ ọrụ, ị nwere ike zoo aka na ntuziaka ntanetị anyị ebe a: www.advateklighting.com/blog/guides
Ị ga-ahụ ozi gbasara njikwa na nhazi nke ngwaọrụ na ntuziaka nhazi PixLite: www.advateklighting.com/downloads/user-manuals/pixlite-configuration-guide
Maka ajụjụ ndị ọzọ, ị nwere ike ịkpọtụrụ ndị otu nkwado anyị na njikọ dị n'okpuru: www.advateklighting.com/contact
support@advateklighting.com

9.5 – Tọgharia ka ọ bụrụ ụlọ nrụpụta
Ka ịtọgharịa onye njikwa na ntọala ntọala ụlọ ọrụ ya, mee ihe ndị a:

1. Ike gbadaa njikwa.
2. Jide bọtịnụ "Factory IP" na bọtịnụ "Bootloader" ọnụ.
3. Mee ka njikwa dị ike.
4. Chere ka ọkụ abụọ ahụ ga-agbanye ọnụ.
5. Hapụ ma bọtịnụ ma gbadaa.
6. Mee ka njikwa dị ike. Ọ ga-enwe nhazi ndabara ụlọ ọrụ ugbu a.

Nkwuputa

Ọ bụrụ na ịchọrọ nkwado ma ọ bụ akwụkwọ ikike, biko rụtụ aka na ngalaba 9.4 maka ozi gbasara ịmepụta tiketi nkwado. Ndị ọrụ nkwado Advatek ga-enyerịrị gị ikike nlọghachi tupu iweghachi ngwaahịa ọ bụla.
Onye njikwa PixLite 16 Long Range Mk2 na ndị nnata na-enye ikike ikike afọ 3 nwere oke yana nkwa nrụzi/nnọchi. Biko hụ usoro na ọnọdụ na anyị websaịtị maka ozi ndị ọzọ.
Art-Net™ Mebere ya na ikike nwebisiinka Artistic License Holdings Ltd.
Emepụtara ngwaahịa a site na:
Ụgwọ nke ụlọ ọrụ Advatek Lighting Pty Ltd
U1, 3-5 Ụlọikpe Gilda
Mulgrave, 3170
VIC, AUSTRALIA

www.advateklighting.com
PixLite 16 Long Range Mk2 User Manual V20250606

Akwụkwọ / akụrụngwa

ADVATEK PixLite 16 Ogologo ogologo Mk2 Pixel Controller [pdf] Akwụkwọ ntuziaka onye ọrụ Hardware Rev 1.0, Hardware Rev 1.1, PixLite 16 Ogologo ogologo Mk2 Pixel Controller, PixLite 16 Ogologo ogologo Mk2, Pixel Controller, Controller

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ