Ihe omume ọkụ APRO4-IP DMX njikwa

Maka nchekwa gị, biko jiri nlezianya gụọ akwụkwọ ntuziaka onye ọrụ a tupu eji ya.
Ọkụ mmemme nwere ikike ịtụgharị akwụkwọ ntuziaka n'oge ọ bụla. Ozi na nkọwapụta dị n'ime akwụkwọ ntuziaka a nwere ike ịgbanwe na-enweghị ọkwa. Ọkụ mmemme anaghị ewere ụgwọ ọ bụla ma ọ bụ ọrụ maka mperi ma ọ bụ ihe ọ bụla. Biko kpọtụrụ Event Lighting maka nkọwa ma ọ bụ ozi ọ bụla gbasara ihe a.

Atụmatụ

• DMX 512, RDM, Artnet and sACN support
• Nhazi ime anya site na ime webibe
• Update firmware on Webibe
• DMX output isolation
• RJ45 Ethernet B input with POE（DC12V 2A）
• Ngosipụta LCD
• Gigabit network, 100/1000mbps port speed
• IP65 ọkwa

ỤLỌ KWESỊRỊVIEW

1. Ethernet port RJ45
2. Ethernet port RJ45
3. Power in/out True1
4. 2xDMX5pin connectors
5. 2xDMX5pin connectors
6. Ihe njide fuse
7. LCD Display protection cover

NKWUO
Below is controller Menus map

IsiNchNhr	Sub menu 1	Sub menu 2	Uru/Nhọrọ	Ọdabara
Netwọk	Ọnọdụ IP		DHCP	Static
			Static
	Adreesị IP		2.xx.xx.xx	2.xx.xx.xx
	Nkpuchi Subnet		255.0.0.0	255.0.0.0
DMX Port	Protocol	Artnet		Artnet
		SACN
	Start Net		000-127	000
	Malite Eluigwe na Ala		000-255	000
	Port 1	Ụdị	Gbanyụọ	On
			On
		NET	000-127	000
		Eluigwe na Ala	000-255	000
	Port 2	Ụdị	Gbanyụọ	On
			On
		NET	000-127	000
		Eluigwe na Ala	000-255	001
	Port 3	Ụdị	Gbanyụọ	On
			On
		NET	000-127	000
		Eluigwe na Ala	000-255	002
	Port 4	Ụdị	Gbanyụọ	On
			On
		NET	000-128	000
		Eluigwe na Ala	000-255	003
			Gbanyụọ
Ntọala	Ọnụego DMX		20Hz	30Hz
			25Hz
			30Hz
			35Hz
			40Hz
	RDM	Gbanyụọ		Gbanyụọ
		Kwado
	Gosipụta Na	Mgbe niile		1Nkeji
		Nkeji 30
		1Nkeji
		5Nkeji
	Mfu mgbaàmà	Jide DMX		Jide DMX
		Stop Output
	Ụdị njikọ	PH		PH
		LTP
	Ntọgharị ụlọ nrụpụta	Mba		Mba
		Ee

WEB nhazi

NET ngwaọrụ netwọk IP mode nwere ike ịtọ ka DHCP mode ma ọ bụ Static mode.

Ọnọdụ DHCP

• When APRO4‐IP is set to DHCP mode, you need to set the computer to DHCP also. And use a router for linking computer and APRO4‐IP device. The controller will show IP address like below:
• Tinye adreesị IP gị web nchọgharị, mgbe ahụ ị nwere ike nbanye webibe iji hazie oke nke njikwa.

Tinye paswọọdụ: admin

Ọnọdụ kwụ ọtọ

• When APRO4‐IP device is set to Static mode, you need to set computer to be Static mode also. APRO4‐IP device will show IP address as below:
• Mgbe ahụ ịtọ adreesị IP nke kọmputa dị n'otu mpaghara IP ahụ na aka gị. Maka example: IP address must start with 2 according to APRO4‐IP address. And netmask is same with 255.0.0.0.
• Input static IP address of APRO4‐IP device in your browser, then you can login to configure the parameter of device.

Tinye paswọọdụ: admin

• Mgbe ịbanye na NET Config web, the first page show the information about APRO4‐IP.
• Following  is  for  Network  setting,  you  can  set  IP  mode  to  be  Static  or  DHCP,  IP  Address,and Subnet Mask. After setting, click Save button .
• Maka ibe DMX Port, a na-eji ya maka ntọala ọdụ ụgbọ mmiri DMX. Ị nwere ike họrọ Protocol ka ọ bụrụ Artnet ma ọ bụ sACN, ma tọọ ọdụ ụgbọ mmiri ọ bụla dị ka ntinye ma ọ bụ mmepụta.
• On the page of Setting , you can set DMX Rate, RDM , Display On and Signal Loss. After setting, click Save to store the setting.
• DMX  Rate:  You  can  set  20Hz,  25Hz,  30Hz,  35Hz,  40Hz,  30Hz  is default setting.
• RDM: You can set RDM to be Disable or Enable.
• There is 4 options for Display On mode: Always, 30Sec, 1Min, 5Min.
• Mfu mgbaàmà: Can set as Hold DMX or Stop Output.
• Ị nwere ike laghachi factory ntọala site pịa Factory Tọgharia bọtịnụ.
• Na ibe mmelite, ị nwere ike imelite ngwanro nke fixture site na ịhọrọ ngwanro mmelite file of APRO4‐IP.
• Na ibe ikpeazụ, ị nwere ike ịtọgharịa paswọọdụ.

Nkọwapụta

• Ike na: AC 100‐240V,50/60Hz
• Oriri ike: AC240V 50HZ 0.05A
• Nha: 215.3×150.5x42mm 4.2W
• Arọ: 1.43kg
• POE 802.3 af
• IP65

Akụkụ

Akwụkwọ ikike

Biko rụtụ aka na onye na-ere ahịa mpaghara gị ma ọ bụ kpọtụrụ mmemme ọkụ. www.event‐lighting.com.au

Ajụjụ a na-ajụkarị

How do I reset the APRO4-IP device to factory settings?

To perform a factory reset on the APRO4-IP device, access the Factory Reset option in the Main Menu under Settings. Confirm the reset to restore the device to its default configuration.

What is the default IP address for the APRO4-IP device?

The default IP address for the APRO4-IP device is set to DHCP mode. If you switch to Static mode, you can set a specific IP address within the range provided in the user manual.

Akwụkwọ / akụrụngwa

Ihe omume ọkụ APRO4-IP DMX njikwa [pdf] Akwụkwọ ntuziaka onye ọrụ APRO4-IP, APRO4-IP DMX njikwa, DMX njikwa, njikwa

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ