Onye njikwa okpomọkụ Brainchild E62 PID
gafereview & Ọdịdị
Igodo na ihe ngosi
Arụ ọrụ igodo
Igodo mpịakọta: 
A na-eji igodo a họrọ oke ka ọ bụrụ viewed ma ọ bụ gbanwee.
Igodo elu/Mbawanye:
A na-eji igodo a iji bulie uru nke oke ahọpụtara.
Igodo ala/Welata: 
A na-eji igodo a belata uru nke oke ahọpụtara.
Igodo SHIFT:
A na-eji igodo a:
- Move to the digit of the selected parameter and change the value by using up or down key to increase or decrease the value.
Scroll Up: 
A na-eji igodo abụọ apịkọrọ ọnụ mee:
- Go to the previous parameter
Tọgharia: + 
A na-eji igodo abụọ apịkọrọ ọnụ mee:
- Weghachite ngosi na ihuenyo ụlọ.
- Tọgharia oti mkpu ozugbo ewepụrụ ọnọdụ mkpu.
- Kwụsị ụkpụrụ njikwa akwụkwọ ntuziaka, ọnọdụ ntugharị akpaaka ma ọ bụ ọnọdụ mmezi.
- Hichapụ ozi njehie akpaaka ma ọ bụ nzikọrịta ozi.
- Enter the manual control menu if a failure mode occurs.
Pịgharịa gaa na ala: 
Two keys pressed synchronously directly go to the Manual control mode
Tinye igodo:
Pịa ma jide 5 sekọnd ma ọ bụ karịa ka:
- Enter the Auto-Tuning mode.
Ngosipụta ga-egosi. - Enter the manual control mode.
Ngosipụta ga-egosi.
Enter the setup menu mode.
Ngosipụta ga-egosi. 
Perform calibration of a selected parameter during the calibration procedure. The display will show
E kewaa menu n'ime otu ise. Ha bụ ndị a:
- Ntinye njirimara
- Auto-Tuning Mode Menu
- NchNhr ụkpụrụ ntuziaka
- Nhazi menu
- Calibration Mode Menu
- Pịa for the next parameter ; Press na igodo ịlaghachi na paramita gara aga.
- Pịa ma jide for 3.1 seconds, then let go to select auto tuning mode.
- Pịa ma jide for 4.2 seconds, then let go, to select manual control mode.
- Pịa ma jide for 5.3 seconds, then let go to select setup mode.
- Pịa ma jide maka sekọnd 6.4, wee hapụzie ka ịhọrọ ọnọdụ nhazi.
Ntinye njirimara
Jiri key to enter basic menu parameters, and press again to select SP1, SEL1~SEL8.
Pịa ịlaghachi na nke gara aga.
Auto-Tuning Mode
Pịa key 5 seconds to activate Auto-Tuning Mode
NchNhr ụkpụrụ ntuziaka
Pịa key 3 seconds to execute the selected default program
Enter Manual Control Mode; refer to Manual 6.1 & 6.8.2~6.8.4
Nhazi menu
The setup menu has been categorized into eight categories.
They are listed as below.
- Isi NchNhr (bASE)
- NchNhr mmepụta (oUT)
- Communication Menu (CoMM)
- User Select Menu (SEL)
Isi NchNhr (bASE)
Jiri or key to get bASE in the lower display then use key to enter to basic menu parameters.
NchNhr mmepụta (oUT)
Jiri or key to get oUT in the lower display then use key to enter to output menu parameters.
Communication Menu (CoMM)
Jiri or key to get CoMM in the lower display then use key to enter to communication menu parameters.
Please note that confirm A2FN set to CoMM when using communication.
User Select Menu (SEL)
Jiri or key get SEL in the lower display then use key to enter to select the user menu parameters.
Ụdị nhazi
Pịa key for 2 seconds or longer (not more than 3 seconds) ; then release it to enter calibration Mode.
Pịa key for 5 seconds to perform calibration
- Please note that it is required to use specialized equipment to apply calibration, attempting to change will affect device accuracy
Mara:
- Using Manual, Auto-Tuning, Calibration modes will break the control loop and change some of the previous setting data. Make sure that the system is allowable to apply these modes.
- The flow chart shows a complete list of all parameters. For actual application, the number of available parameters will vary depending on the setup and model of the controller and will be less than that shown in the flow chart.
- The user can select up to 8 parameters to put in the user select menu by using the SEL1~SEL8 parameters in the setup menu
Tupu ịmalite, Tọọ ntinye/mmepụta
Mgbe emelitere, pịa ma jide for 5.3 seconds, then let go to enter Setup Menu. Complete Parameter setting, INPT, UNIT, DP, O1TY, O1L and O1H.
- Enter the Setup Menu. Press for 5 seconds to enter Basic Menu (bASE). Finish setting for INPT, UNIT and DP. Exit the level.
- Return to the Setup Menu. Press for 5 seconds to enter Output Menu (oUT). Finish setting for O1TY, O1L and O1H. Press and hold ma laghachi na homepage.
Okpokoro OP1L/OP1H
| Oke | OP1L | OP1H | |
| OM9A-3 | 4-20 | 20.0 | 100.0 |
| OM9A-3 | 0-20 | 0.0 | 100.0 |
| OM9A-5 | 0-5V | 0.0 | 50.0 |
| OM9A-5 | 1-5V | 10.0 | 50.0 |
| OM9A-5 | 0-10 | 0.0 | 100.0 |
* When O1TY as DC.MA or DC. Vo, set the value based on usage requirement
Njikọ ọnụ
Nkọwapụta oke
User Menu Parameter
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta | |
| 0 | SP1 | Tọọ ihe 1 | Ala: SP1L
Ọnụ: SP1H |
25.0 Celsius C | R/W | |
| 64 | PV | Usoro uru | Ala: -19999
elu: 45536 |
(77.0 Celsius F) | R | |
| 65 | SV | Uru ihe atọrọ ugbu a | Ala: SP1L
Ọnụ: SP1H |
—— | R | |
| 44 |
SEL1 |
Họrọ paramita nke mbụ maka menu onye ọrụ | 0 Ọ BỤGHỊ
1 A1SP 2 A2SP 3 Mkpọchi 4 INPT 5 PB 6 TI |
7 TD
8 SHIF 9 OFST 10 O1HY 11 A1HY 12 A2HY 13 ADDR |
—— | R/W |
| 45 | SEL2 | Select 2nd parameter | Select 2nd parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 46 | SEL3 | Select 3rd parameter | Select 3rd parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 47 | SEL4 | Select 4th parameter | Select 4th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 48 | SEL5 | Select 5th parameter | Select 5th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 49 | SEL6 | Select 6th parameter | Select 6th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 50 | SEL7 | Select 7th parameter | Select 7th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 51 | SEL8 | Select 8th parameter | Select 8th parameter for user manual. Same as the SEL1 | 0 | R/W | |
Manual Mode Parameter
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
| 66 | MV1 | Mpụta 1% Uru | Ala: 0.00
Elu: 100.00% |
—- | R (R/W,
Akwụkwọ ntuziaka) |
Basic (bASE) Parameter
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
| 3 | Mkpọchi | Họrọ paramita a ga-akpọchi | 0 Ọ dịghị: Ọ dịghị oke ihe akpọchiri
1 SEt: Setup data are locked 2 uSEr: Setup data and user data are locked. SetPoint are unlocked. 3 ALL: All data are locked |
0 | R/W |
| 4 | INPT | Input sensor selec- tion | 0 J_tC: J ụdị Thermocouple
1 K_tC: K ụdị Thermocouple 2 t_tC: T type Thermocouple 3 R_tC: R ụdị Thermocouple 4 S_tC: S type Thermocouple 5 Pt. dN: PT 100 DIN 6 Pt.JS: PT 100 JIS |
1 | R/W |
| 5 | UNIT | Nhọrọ nkeji ntinye | 0 oC: °C unit
1 oF: °F unit |
0 | R/W |
| 6 | DP | Decimal point selec- tion | 0 No.dP: no decimal point
1 1-dP: 1 nkeji iri |
1 |
R/W |
|
9 |
SP1L |
Oke dị ala nke uru ntụpọ atọrọ | Ala:
J_TC: -120.0°C (-184.0°F) K_TC: -200.0°C (-328.0°F) T_TC: -250.0°C (-418.0°F) R_TC: 0.0°C ( 32.0°F) S_TC: 0.0°C ( 32.0°F) PTDN: -200.0°C (-328.0°F) PTJS: -200.0°C (-328.0°F) Ọnụ: SP1H |
-17.8 Celsius
(0.0 Celsius F) |
R/W |
| 10 |
SP1H |
Oke dị elu nke uru ihe setịpụrụ | Ala: SP1L
Elu: J_TC: 1000.0°C (1828.0°F) K_TC: 1370.0°C (2498.0°F) T_TC: 400.0°C ( 752.0°F) R_TC: 1767.7°C (3214.0°F) S_TC: 1767.7°C (3214.0°F) PTDN: 850.0°C (1562.0°F) PTJS: 600.0°C (1112.0°F) |
537.8 Celsius C
(1000.0 Celsius F) |
R/W |
| 12 | MGBE |
Nyo damping time constant of PV |
0 0: 0 nkeji oge na-adịgide adịgide
1 0.2: 0.2 nkeji oge na-adịgide adịgide 2 0.5: 0.5 nkeji oge na-adịgide adịgide 3 1: 1 nkeji oge na-adịgide adịgide 4 2: 2 nkeji oge na-adịgide adịgide 5 15: 5 nkeji oge na-adịgide adịgide 6 10: 10 nkeji oge na-adịgide adịgide 7 20: 20 nkeji oge na-adịgide adịgide 8 30: 30 nkeji oge na-adịgide adịgide 9 60: 60 nkeji oge na-adịgide adịgide |
2 | R/W |
| 14 | PB | Oke bandwit
uru |
Ala: 0.0
Elu: 500.0°C (900.0°F) |
10.0 Celsius C
(18.0 Celsius F) |
R/W |
| 15 | TI | Ọnụ ahịa oge ọnụ | Low: 0, High: 3600 sec | 60 | R/W |
| 16 | TD | Uru oge ewepụtara | Low: 0, High: 360.0 sec | 30.0 | R/W |
| 11 | SHIF | PV shift (offset)
uru |
Low: -200.0°C (-360.0°F) High: 200.0°C (360.0°F) | 0.0 Celsius C
(0.0 Celsius F) |
R/W |
| 68 | CICF | Mgbanwe nzacha CIC | 0 Gbanyụọ
1 NA |
0 | R |
Output (oUT) Parameter
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
| 17 | ỌPỌ1 | Mmepụta 1 ọrụ | 0 REVR: Reverse (heating) control action
1 dIRt: Direct (cooling) control action |
0 | R/W |
| 21 | CYC1 | Mmepụta 1 okirikiri oge | Low: 0.1;
Elu: 90.0 sk. |
18.0 | R/W |
| 18 | O1TY | Ụdị mgbama 1 mmepụta | 0 RELY: Mmepụta mbugharị
1 SSrd: Mwepụta draịva relay steeti siri ike 2 DC.MA: DC current 3 DC.Vo: DC voltage |
0 | R/W |
| 7 | OP1L | OP1 linear mmepụta uru oke dị ala | 0.0 ~ OP1H | 0.0 | R/W |
| 8 | OP1H | OP1 linear output
high limit value |
OP1L ~ 110.0% | 100.0 | R/W |
| 19 | O1FT | Mmepụta 1 ọnọdụ mbufe ọdịda | 0~1000: 0.0 ~ 100.0 % to continue output 1
control function if the sensor fails, or select OFF (0) or ON (1) for ON-OFF control |
0.0 | R/W |
| 22 | OFST | Offset value for P
njikwa |
Ala: 0
Elu: 100.0% |
25.0 | R/W |
| 20 | O1HY | Output 1 ON-OFF
control hysteresis |
Ala: 0.1
Elu: 50.0C (90.0F) |
0.5 Celsius C
(0.9 Celsius F) |
R/W |
| 23 | PL1L | MV1 power value
oke ala |
Ala: 0
Elu: 50% ma ọ bụ PL1H |
0 | R/W |
| 24 | PL1H | MV2 power value limit high | Ala: PL1L
Elu: 100% |
100 |
R/W |
| 25 | A1FN | Ọrụ mkpu 1 maka mpụta 1 mkpu | 0 Ọnweghị: Ọ nweghị ọrụ mkpu
1 dE.HI: Mgbanwe dị elu mkpu 2 dE.Lo: Mgbanwe dị ala 3 db.HI: Deviation band out of band alarm 4 db.Lo: Mgbapụ ngbanwe na mkpu band 5 PV.HI: Usoro uru mkpu dị elu 6 PV.Lo: Usoro uru mkpu dị ala |
1 |
R/W |
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
|
26 |
A1MD |
Alarm 1 operation mode |
0 NoRM: Omume mkpu nkịtị
1 LtCH: Latching alarm action 2 Jide: Jide mmemme oti mkpu 3 Lt.Ho: Latching & Jide ihe |
0 | R/W |
| 29 | A1HY | Alarm 1 Hysteresis control | Ala: 0.1
Elu: 50.0°C (90.0°F) |
0.1 Celsius C
(0.2 Celsius F) |
R/W |
| 34 | A1DL | Mkpu 1 igbu oge | Ala: 0; Elu: 5999 sk | 0 | R/W |
| 28 | A1FT | Alarm 1 failure trans- fer mode | 0 oFF: OFF if sensor fails
1 on: Gbanye ma ọ bụrụ na ihe mmetụta ada ada |
1 | R/W |
| 1 | A1SP | Oti mkpu 1 ebe atọrọ | A1FN=PVHI/PVLO
Ala: SP1L Elu: SP1H |
100.0 Celsius C
(212.0 Celsius F) |
R/W |
| 13 | A1DV | Alarm 1 deviation value | A1FN=DEHI/DELO/DBHI/DBLO
Ala: 0.0 Elu: 500.0°C (900.0°F) |
10.0 Celsius C
(18.0 Celsius F) |
R/W |
| 33 |
A2FN |
Ọrụ mkpu 2 maka mpụta 2 mkpu |
0 Ọnweghị: Ọ nweghị ọrụ mkpu
1 dE.HI: Mgbanwe dị elu mkpu 2 dE.Lo: Mgbanwe dị ala 3 db.HI: Deviation band out of band alarm 4 db.Lo: Mgbapụ ngbanwe na mkpu band 5 PV.HI: Usoro uru mkpu dị elu 6 PV.Lo: Usoro uru mkpu dị ala 7 COMM: RS485 |
2 |
R/W |
|
35 |
A2MD |
Alarm 2 operation mode |
0 NoRM: Omume mkpu nkịtị
1 LtCH: Latching alarm action 2 Jide: Jide mmemme oti mkpu 3 Lt.Ho: Latching & Jide ihe |
0 |
R/W |
| 36 | A2HY | Hysteresis control of alarm 2 | Obere ala: 0.1°C
Elu: 50.0°C (90.0°F) |
0.1 Celsius C
(0.2 Celsius F) |
R/W |
| 38 | A2DL | Mkpu 2 igbu oge | Ala: 0; Elu: 5999 sk | 0 | R/W |
| 37 | A2FT | Alarm 2 failure forced transfer mode | 0 oFF: Alarm output OFF if sensor fails
1 oN: Alarm output ON if sensor fails |
1 | R/W |
| 2 | A2SP | Oti mkpu 2 ebe atọrọ | A2FN=PVHI/PVLO
Ala: SP1L Elu: SP1H |
100.0 Celsius C
(212.0 Celsius F) |
R/W |
| 43 | A2DV | Alarm 2 deviation value | A2FN=DEHI/DELO/DBHI/DBLO
Ala: 0.0 Elu: 500.0°C (900.0°F) |
10.0 Celsius C
(18.0 Celsius F) |
R/W |
Communication (CoMM) Parameter
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
| 39 | ADDR | Address assignment of digital nzikọrịta ozi |
Ala: 1
elu: 255 |
1 | R/W |
| 40 | BAUD | Baud ọnụego nke dijitalụ nkwurịta okwu | 0 2.4: 2.4 Kbits/s baud rate
1 4.8: 4.8 Kbits/s baud rate 2 9.6: 9.6 Kbits/s baud rate 3 14.4: 14.4 Kbits/s baud rate 4 19.2: 19.2 Kbits/s baud rate 5 28.8: 28.8 Kbits/s baud rate 6 38.4: 38.4 Kbits/s baud rate 7 57.6: 57.6 Kbits/s baud rate 8 115.2: 115.2 Kbits/s baud rate |
2 | R/W |
| 41 | DATA | Data bit count of dig- ital communication | 0 7bI: 7 bit
1 8bI: 8 bit |
1 | R/W |
| 42 | PARI | The parity bit of digi- tal communication | 0 EVEN: Even parity
1 odd: Odd parity 2 NoNE: No parity bit |
0 |
R/W |
Calibration Mode Parameter
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
| 52 | ADLO | mV calibration low
ọnụọgụgụ |
Ala: -1999
elu: 1999 |
—- |
R/W |
| 53 | ADHI | mV calibration high
ọnụọgụgụ |
Ala: -1999
elu: 1999 |
—- |
R/W |
| 54 | RTDL | RTD calibration low
ọnụọgụgụ |
Ala: -1999
elu: 1999 |
—- |
R/W |
| 55 | RTDH | RTD calibration high coefficient | Ala: -1999
elu: 1999 |
—- |
R/W |
| 56 | CJLO | Cold junction calibra-
tion low coefficient |
Ala: -5.00
elu: 40.00 |
—- |
R/W |
Parameter ndị ọzọ
| Modbus | Oke | Nkọwa | Oke | Ọdabara | Nweta |
| 57 | CJCT | Okpomọkụ Junction | Ala: -4000
elu: 9000 |
—- | R |
| 58 | ỤBỌCHỊ | Ụbọchị | Low: 0;
elu: 65535 |
—- | R |
| 59 | SRNO | Nọmba usoro n'usoro | Low: 0;
elu: 65535 |
—- | R |
| 63 | CJCL | Cold junction low calibration
voltage |
Ala: 0
elu: 7552 |
—- | R |
| 69 | EROR | Koodu mperi | Ala: 0; Ọnụ: 65535 | —- | R |
| 70 | MODE | Ụdị ọrụ & ọkwa mkpu | Ala: 0
elu: 65535 |
—- | R |
| 71 | ỌRỤ | Device version, firmware version | 67.XX | —- | R |
| 72 | CMND | Koodu iwu | Ala: 0; Ọnụ: 65535 | —- | R/W |
| 73 | JOB1 | Koodu ọrụ | Ala: 0; Ọnụ: 65535 | —- | R/W |
Koodu mperi
| Njehie Koodu | Ngosipụta
Akara |
Nkọwa & Ihe kpatara ya |
Ndozi Omume |
| 10 | ER10 | Njehie nkwukọrịta: koodu ọrụ ọjọọ | Correct the communication software to meet the protocol
chọrọ |
| 11 | ER11 | Njehie nzikọrịta ozi: debanye aha adreesị na-enweghị oke | Enyela ohu ahụ adreesị akwụkwọ ndekọ aha karịrị oke |
| 14 | ER14 | Communication error: attempt to write a
read-only data |
Edela data naanị ọgụgụ ma ọ bụ data echedoro nye ohu ahụ |
| 15 | ER15 | Njehie nzikọrịta ozi: dee uru na-enweghị oke na ndebanye aha | Edela ihe karịrị oke data na ndekọ ohu |
| 26 | ATER | Auto-Tuning Error: Failed to perform Auto-Tuning function |
|
| 29 | EEPR | Enweghị ike ide EEPROM nke ọma | Laghachi na onye nrụpụta maka ịrụzi. |
| 30 | CJER | Ụgwọ nkwụsịtụ oyi maka
Thermocouple adịghị arụ ọrụ |
Laghachi na onye nrụpụta maka ịrụzi. |
| 39 | SBER | Input sensor break | Replace the input sensor |
| 40 | ADER | Ihe ntụgharị A ruo D ma ọ bụ ihe ndị metụtara ya adịghị arụ ọrụ | Laghachi na onye nrụpụta izizi maka ndozi. |
FAQ
Kedu ka m ga-esi nweta NchNhr njirimara?
To access the User Menu, press the corresponding key on the controller.
Kedu otu m ga-esi mee ka ọnọdụ-emegharị akpaaka?
To activate Auto-Tuning Mode, press and hold a specific key for 5 seconds.
How do I enter Manual Control Mode? To enter Manual Control Mode, press the designated key for 3 seconds. How do I perform calibration? To calibrate a parameter, press and hold the ENTER key for 5 seconds during the calibration procedure.
To enter Manual Control Mode, press the designated key for 3 seconds.
Kedu ka m ga-esi mee nhazi nhazi?
To calibrate a parameter, press and hold the ENTER key for 5 seconds during the calibration procedure.
Akwụkwọ / akụrụngwa
 |
Onye njikwa okpomọkụ Brainchild E62 PID [pdf] Akwụkwọ ntuziaka E62, QS0E620C, E62 PID okpomọkụ njikwa, E62, PID okpomọkụ njikwa, okpomọkụ njikwa, njikwa |