Okwu mmalite
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your GAME 7011-E Sand Filtration System. This system is designed for above-ground pools up to 25,000 gallons, featuring a 16-inch filter tank, a 3/4 HP pump, and a digital timer for automated filtration cycles. Please read all instructions carefully before assembly and use.
Ozi nchekwa
ỊDỌ AKA NA NTỊ: Ọ bụrụ na ị gbasoghị ntuziaka ndị a, ọ ga-akpata nnukwu mmerụ ahụ ma ọ bụ ọnwụ.
- Always disconnect power to the pump before performing any service or maintenance.
- Ensure the electrical supply is protected by a Ground Fault Circuit Interrupter (GFCI).
- Ejila ọkpọkọ ahụ rụọ ọrụ ma ọ bụrụ na eriri ọkụ ma ọ bụ plọg ahụ emebie.
- Keep children away from the filtration system during operation.
- The system must be installed on a solid, level surface.
- Eliela eriri ike.
- Consult a qualified electrician for electrical connections if unsure.
Ihe ngwugwu
Nyochaa na akụrụngwa niile edepụtara n'okpuru dị ugbu a na emebighị ya tupu ịmalite mgbakọ.
Image: A visual representation of all components included in the package, such as the six-way valve, sand filter tank, pump, hoses, and hardware.
- Six-Way Valve
- 16-inch Sand Filter Tank
- 16-inch Sand Filter Tank Base
- 16-inch Manifold Tube
- Manifold Lateral Assembly
- Flange Clamp
- 0.75 HP Pump & Motor Assembly & Base
- Ọta ájá
- Fasteners, Hardware & Gaskets
- Nleba nrụgide
- Sand Filter Tank Drain Plug
- 20", 40" & 120" Hoses
- Nkata Strainer
- Strainer Basket Lid
- Motor Drain Plug
- Igwe nlegharị anya
Mgbakọ na ntinye
Follow these steps for proper assembly and installation of your sand filtration system.
Image: The complete GAME 7011-E Sand Filtration System, including the sand filter tank, pump, and multi-port valve.
- Debe sistemụ ahụ: Place the filter system on a firm, level surface, preferably concrete, at least 2 feet from the pool. Ensure the location allows for proper drainage when backwashing.
- Assembling the Tank Base: Secure the sand filter tank onto its base.
- Installing Lateral Assembly: Insert the manifold lateral assembly into the bottom of the filter tank. Ensure laterals are spread evenly.
- Adding Filter Sand: Carefully pour approximately 120 pounds of #20 silica sand (0.45-0.55mm) into the filter tank. Ensure the manifold tube remains centered during this process. Fill the tank about two-thirds full.
- Attaching the Six-Way Valve: Place the six-way valve onto the top of the filter tank, aligning the ports. Secure it with the flange clamp, ensuring a tight seal. Use a #3 Phillips screwdriver for the clamp screws and ensure washers are used to prevent damage to the plastic flange. Align the clamp openings with the ridges on the valve.
- Ijikọ mgbapụta ahụ: Attach the pump to the six-way valve using the provided hoses and fittings. Ensure all connections are tight to prevent leaks. The system uses 1.5-inch inlet and outlet connections.
- Connecting to Pool: Connect the pool's skimmer line to the pump's inlet and the pool's return line to the six-way valve's 'RETURN' port using the provided hoses.
- Installing Pressure Gauge: Screw the pressure gauge into the designated port on the six-way valve.
- Filling the Pump with Water: Before starting, remove the strainer basket lid and fill the pump with water to prime it. Replace the lid securely.
- Njikọ eletrik: Plug the 7.9-meter power cord into a GFCI-protected outlet.
Image: The compact sand filtration system positioned beside an above-ground pool, demonstrating its suitable size for various setups.
Ọrụ
The GAME 7011-E Sand Filtration System features a 6-way valve and a digital timer for controlling filtration cycles.
Foto: Ofeview highlighting the pressure gauge for monitoring system performance, the 6-way valve for controlling water flow, and the strainer basket for pre-filtering debris.
6-Way Valve Functions
Always turn off the pump before changing the valve position to prevent damage.
- Nzacha: Normal filtering mode. Water flows through the sand, trapping debris, and returns to the pool.
- BAKWASH: Cleans the filter sand by reversing water flow, sending dirty water to waste. Use when pressure gauge reads 8-10 PSI above starting pressure.
- SINU: Used after backwashing to flush out any remaining dirty water from the valve and sand bed to waste before returning to FILTER mode.
- WASTE/DRAIN: Bypasses the filter, sending water directly to waste. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
- KWESỊRỊ: Bypasses the filter, circulating water directly back to the pool. Useful for mixing chemicals without filtering.
- Emechiri: Shuts off all flow to the filter and pump. Use for servicing the pump or filter.
Ọrụ ngụ oge dijitalụ
Image: Close-up of the integrated digital timer, allowing for programmable filtration cycles.
The digital timer allows for automated control of filtration cycles. Refer to the timer's specific instructions for setting daily run times. Ensure the timer is set to provide adequate filtration for your pool size and usage, typically 8-12 hours per day.
Nlekọta
Regular maintenance ensures optimal performance and longevity of your filtration system.
- Ịsacha azụ: Perform backwashing when the pressure gauge reads 8-10 PSI above its clean starting pressure, or when water flow to the pool decreases significantly.
- Ịsa mmiri: Always rinse for 30-60 seconds after backwashing to settle the sand and prevent dirty water from returning to the pool.
- Ịsacha Nkata: Regularly inspect and clean the pump's strainer basket. Turn off the pump, close necessary valves, remove the lid, empty debris, and replace.
- Ndochi ájá: Filter sand typically needs to be replaced every 3-5 years, depending on usage and water chemistry.
- Oge oyi: In cold climates, drain all water from the pump and filter tank to prevent freezing damage. Store the pump and valve indoors if possible.
Nchọpụta nsogbu
This section addresses common issues you might encounter with your sand filtration system.
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Mmiri na-agbapụta site na njikọ | Loose fittings, worn O-rings/gaskets, improper clamp nhazi. | Tighten all connections. Inspect and replace O-rings/gaskets if damaged. Ensure flange clamp is correctly aligned and tightened. |
| Aja na-alaghachi na ọdọ mmiri | Damaged laterals, incorrect sand type/size, insufficient rinse after backwash. | Check laterals for damage. Ensure correct #20 silica sand is used. Perform a thorough rinse cycle after backwashing. |
| Obere mmiri eruba/nrụgide | Clogged strainer basket, dirty filter sand, air in the system, closed valves. | Clean strainer basket. Backwash and rinse filter. Bleed air from the system. Ensure all necessary valves are open. |
| Mgbapu adịghị priming | Insufficient water in pump, air leak in suction line, clogged skimmer/main drain. | Fill pump with water. Check all suction line connections for air leaks. Clear any blockages in skimmer or main drain. |
| Excessive pump noise | Lack of water, air in system, cavitation, motor bearing issue. | Ensure pump is fully primed. Check for air leaks. Verify adequate water supply to pump. If noise persists, contact support. |
Nkọwapụta
| Njirimara | Nkọwa |
|---|---|
| Ụdị | Egwuregwu |
| Nọmba nlereanya | 7011-E |
| Mgbapụta Ike Ịnyịnya | 0.75 HP |
| Ọnụego mgbapụta mgbapụta | Ihe dị ka 3,698 GPH |
| Ogo tankị nzacha | 16-anụ ọhịa |
| Ike ájá | 120 pound |
| Max Pool Capacity | Ihe ruru 25,000 galọn |
| Inlet/Outlet Connection Size | 1.5 sentimita asatọ |
| Ogologo eriri ike | 7.9 mita |
| Akụkụ (L x W x H) | 15.7 x 26.7 x 30.1 sentimita asatọ |
| Ibu Ibu | 42.7 pound |
| Njirimara nchekwa | GFCI arụnyere n'ime ya |
Akwụkwọ ikike na nkwado
The GAME 7011-E Sand Filtration System comes with a 2-afọ emeputa akwụkwọ ikike. For warranty claims, technical assistance, or replacement parts, please contact GAME customer support. Refer to the product packaging or the official GAME websaịtị maka ozi kọntaktị ugbu a.
Image: The sand filtration system integrated with a GAME SCG (Saltwater Chlorinator Generator) system, illustrating compatibility.