CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser User Manual

Okwu mmalite

Thank you for choosing the CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser. This advanced system provides convenient access to purified cold and ambient water. Featuring a GAC filtration system, UV LED self-cleaning, and touchless dispense technology, it ensures a hygienic and refreshing hydration experience. This manual provides essential information for proper setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your dispenser.

Foto 1: N'ihu view of the CLOVER D25-B-TL Water Cooler Dispenser.

Ozi nchekwa dị mkpa

Biko gụọ ntuziaka niile nke ọma tupu i jiri ngwa ahụ. Debe akwụkwọ ntuziaka a maka ntụnye aka n'ọdịnihu.

• Nchekwa Eletriki: Ensure the dispenser is connected to a grounded electrical outlet. Do not use extension cords. Disconnect power before cleaning or servicing.
• Njikọ mmiri: Connect the dispenser only to a potable water supply. Ensure all connections are secure to prevent leaks.
• Nkwanye: Place the dispenser on a flat, stable surface. Allow adequate clearance around the unit for ventilation.
• Ụmụaka na anụ ụlọ: Keep children and pets away from the dispenser, especially during operation and maintenance.
• Okpomọkụ: This unit dispenses cold and ambient water only. It does NOT produce hot water.
• Mmebi: Do not operate the dispenser if it has a damaged cord or plug, or if it has been dropped or damaged in any way. Contact customer support.

Ihe ngwugwu

Verify that all items listed below are included in your package.

• CLOVER D25-B-TL Water Cooler Dispenser
• First Filter (GAC Purification System)
• Mmiri tubing
• Njikọ
• Emergency Shutoff Valve
• Tubing Clips
• Akwụkwọ ntuziaka onye ọrụ

Foto nke 2: Ihe ndị dị na ngwa nrụnye gụnyere.

Ntuziaka nhazi

1. Iwepu: Carefully remove the dispenser and all components from the packaging. Retain packaging for future transport if needed.
2. Nkwanye: Position the freestanding dispenser on a level, stable surface. Ensure there is adequate space around the unit for proper ventilation, especially at the rear where the cooling coils are located. The dimensions are approximately 13.58"D x 12.2"W x 43.3"H.
3. Ntinye nyocha:
   • Locate the filter housing, typically at the rear or bottom access panel of the unit.
   • Insert the provided GAC purification filter into the housing as per the arrows indicating water flow.
   • Secure the filter firmly.
   

   Ọgụgụ 3: Ime view illustrating filter placement and water tubing.
4. Njikọ nnweta mmiri:
   • Connect the water tubing from your potable water source to the dispenser's inlet using the provided connectors and emergency shutoff valve.
   • Ensure all connections are tight to prevent leaks. Use tubing clips to secure the tubing if necessary.
   • Slowly open the water supply valve to allow water to fill the dispenser's internal tank. Check for any leaks.
5. Njikọ ike: Plug the dispenser into a grounded 120V AC electrical outlet.
6. Mwepụ mbụ: Before first use, dispense several cups of water from both cold and ambient spouts to flush the system and filter. Discard this water.

Ntuziaka ọrụ

The CLOVER D25-B-TL features touchless dispense and UV LED self-cleaning for enhanced hygiene.

1. Ike Na: Once plugged in, the dispenser will begin to cool the water. Allow approximately 1-2 hours for the water to reach optimal cold temperature (35.6°F).
2. Dispensing Water (Touchless):
   • Place your cup or container under the desired spout (cold or ambient).
   • Wave your hand in front of the sensor located above the spout. The water will begin to dispense.
   • Remove your hand to stop the water flow.
   

   Figure 4: Detail of the touchless dispense spouts and sensors.

3. UV LED Self-Cleaning: The dispenser is equipped with a UV LED self-cleaning system for enhanced water purification. This system operates automatically to maintain the hygiene of the internal water tanks. Refer to the indicator lights on the top panel for its status.

Nlekọta

Regular maintenance ensures the best performance and water quality from your dispenser.

1. Ndochi nzacha:
   • The GAC purification filter should be replaced periodically, typically every 6 months or as indicated by the dispenser's filter change indicator (if present).
   • Turn off the water supply and unplug the dispenser before replacing the filter.
   • Follow the filter installation steps in the Setup section to replace the old filter with a new one.
   • Flush the new filter as described in the Initial Flush step.
2. Nchacha tray Drip: The ABS drip tray is easily removed for cleaning.
   • Pull the drip tray forward to remove it.
   • Empty any collected water and wash the tray with mild soap and water.
   • Rinse thoroughly and reinsert the tray.
3. Nchacha mpụta: Jiri nwayọ hichaa elu mpụta, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
4. Ichacha tankị dị n'ime: The UV LED self-cleaning system helps maintain internal hygiene. For additional cleaning, consult the manufacturer's website or customer support for specific instructions.

Nchọpụta nsogbu

Tupu ịkpọtụrụ nkwado ndị ahịa, biko rụtụ aka na nsogbu na azịza ndị a na-ahụkarị:

Nkọwapụta

Ọgụgụ 5: Akụkụ ngwaahịa maka ntụnye ntinye.

Akwụkwọ ikike na nkwado ndị ahịa

For warranty information, product registration, or technical assistance, please contact CLOVER customer support.

Onye nrụpụta: Clover
Websaịtị: CLOVER Official Store (maka ozi ngwaahịa izugbe)
Biko lee akwụkwọ ịzụrụ ihe gị maka usoro akwụkwọ ikike na nkọwa kọntaktị kpọmkwem.