ShockFlo Type 2 EV Charging Cable (Schuko, 32A, 7kW, 6m) User Manual

1. Okwu mmalite

Thank you for choosing the ShockFlo Type 2 EV Charging Cable. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your EV charger. Please read this manual thoroughly before using the product and retain it for future reference.

This portable EV charging cable is designed to provide a convenient and reliable charging solution for your electric vehicle, offering adjustable current settings and a delayed start function to optimize your charging experience.

2. Ntuziaka nchekwa

Always adhere to the following safety guidelines to prevent injury, damage, or malfunction:

Ensure the charging cable and connectors are free from damage before each use. Do not use if any part is damaged.
Connect the charger only to a properly grounded CEE 1-phase socket that meets local electrical codes.
Do not immerse the control box or connectors in water. While the unit is IP67 waterproof, it is not designed for submersion.
Debe ụmụaka na anụ ụlọ n'ebe a na-akwụ ụgwọ mgbe a na-arụ ọrụ.
Avoid touching the charging pins directly.
Do not attempt to open, disassemble, or modify the charger. This will void the warranty and may cause safety hazards.
The charger is equipped with 10 safety protections, including lightning protection, current leakage protection, ground fault protection, undervoltage nchebe, overvoltage protection, overload protection, overheating protection, and overcurrent protection.
In case of any abnormal operation or error, immediately disconnect the charger from the power source and the vehicle.

Diagram illustrating 10 safety protection designs of the ShockFlo EV charger — This image displays the 10 safety protection designs integrated into the ShockFlo EV charger, including protection against lightning, leakage, ground faults, overvoltage, na -agbadatage, overcurrent, overload, and overheating. The unit is also IP67 waterproof and TUV certified.

3. Ngwaahịa gafereview

3.1 Akụkụ

ShockFlo Type 2 EV Charging Cable with CEE 1-phase plug (32A, 7kW, 6m)
Control Box with LCD Display
Type 2 Vehicle Connector
Detachable Controller Holder (for wall mounting)
Akpa nchekwa

ShockFlo Type 2 EV Charging Cable with control box, Type 2 connector, CEE plug, and storage bag — A zuru oke view of the ShockFlo Type 2 EV Charging Cable, showing the control box, the Type 2 vehicle connector, the CEE 1-phase power plug, and the included storage bag.

3.2 Atụmatụ

Nchaji ngwa ngwa: Delivers up to 7kW power, providing approximately 40 km of range per hour at 230V, 32A.
Ugbu a enwere ike idozi: Selectable current settings (10A, 16A, 20A, 24A, 32A) to match your electrical circuit capacity.
Ọrụ Mmalite Egbughị Oge: Schedule charging to begin at a later time, allowing you to take advantage nke oyi-elu ọkụ eletrik ọnụego.
2-na-1 imewe: Functions as both a portable charger and a wall-mounted charging station with the included detachable holder.
6-Meter Cable: Na-enye ample reach for convenient charging.
Ndakọrịta sara mbara: Compatible with all Type 2/CCS charging ports, suitable for most electric vehicles including Volkswagen, Tesla, Renault, Hyundai, SMART, Opel, Skoda, and BMW.
Ngosipụta LCD HD: Clearly shows real-time charging data such as current, charging rate, and voltage.
Nrụpụta siri ike: Made from high-quality, shock-resistant, and drop-proof materials.

Graphic illustrating 6 times faster charging with 32A, providing 40km range in 1 hour — This image highlights the fast charging capability of the ShockFlo EV charger, showing that 1 hour of charging at 32A can provide approximately 40 km of range.

Image showing compatibility of the Type 2 EV charger with various car brands — This image demonstrates the wide compatibility of the Type 2 EV charger, listing various electric vehicle brands such as Volkswagen, Tesla, Renault, Hyundai, SMART, Opel, Skoda, and BMW.

4. Nhazi

4.1 Wall-Mounted Installation (Optional)

If you prefer a fixed charging station, use the detachable controller holder to mount the control box to a suitable wall. Ensure the mounting location is secure, protected from direct sunlight and heavy rain, and within reach of your vehicle and a CEE 1-phase power outlet.

Select a sturdy wall surface capable of supporting the charger's weight.
Mark the drilling points using the detachable holder as a template.
Drill holes and insert appropriate wall anchors.
Secure the detachable holder to the wall using screws.
Slide the control box onto the mounted holder.

4.2 Ojiji enwere ike ibugharị

For portable use, simply place the control box on a stable, dry surface near your vehicle and the power outlet. Ensure the cable is not stretched or kinked.

Image showing the 2-in-1 functionality of the EV charger as both a wall-mounted and mobile unit — This image illustrates the versatility of the ShockFlo EV charger, demonstrating its use as both a fixed wall-mounted charging station and a portable charging solution for electric vehicles.

5. Ntuziaka ọrụ

5.1 Usoro Nchaji Isi

Ensure your vehicle is parked and turned off.
Plug the CEE 1-phase power plug into a suitable wall socket. The control box LCD will illuminate.
Mepee mkpuchi ọdụ ụgbọ ala gị.
Insert the Type 2 vehicle connector firmly into your vehicle's charging port. Ensure it clicks into place.
The charger will initiate a self-check, and then charging will begin automatically with the last set current. The green indicator light will flash.
To stop charging, first disconnect the Type 2 connector from the vehicle, then unplug the CEE power plug from the wall socket.

5.2 Adjusting Current

Before connecting the Type 2 connector to your vehicle, you can adjust the charging current:

With the CEE plug connected to the wall socket but the Type 2 connector not yet connected to the vehicle, press the 'CURRENT' button on the control box.
Cycle through the available current options: 10A, 16A, 20A, 24A, 32A.
Select the desired current based on your vehicle's requirements and your electrical circuit's capacity.
Once the current is set, connect the Type 2 connector to your vehicle to begin charging.

5.3 Setting Delayed Start

To schedule charging for a later time:

With the CEE plug connected to the wall socket but the Type 2 connector not yet connected to the vehicle, press the 'DELAY' button on the control box.
Each press will increase the delay time in hourly increments (e.g., 1 hour, 2 hours, up to 12 hours).
Once the desired delay is set, connect the Type 2 connector to your vehicle. The charger will display the countdown and begin charging after the set delay.

Control box display showing adjustable current settings and delayed start time options — This image illustrates the control box interface, detailing how to adjust the charging current (10A to 32A) and set a delayed start time for charging, which can help save on electricity costs.

5.4 Ihe ngosi ọkụ

Green Light Na: Ebubo zuru oke.
Ọkụ Green na-egbuke egbuke: Ịchaji na-aga n'ihu.
Ọkụ na-acha uhie uhie: Ụdị njikere.
Ọkụ na-acha uhie uhie: Error detected. Refer to the Troubleshooting section.

Diagram explaining the meaning of red and green indicator lights on the EV charger — This diagram clarifies the status indicated by the charger's LED lights: a red light signifies standby or an error (if flashing), while a green light indicates charging in progress (if flashing) or a full charge (if solid).

6. Nlekọta

Nhicha: Disconnect the charger from all power sources and the vehicle before cleaning. Use a soft, dry cloth to wipe the control box and cables. Do not use harsh chemicals or abrasive cleaners.
Nchekwa: When not in use, store the charging cable neatly in the provided storage bag. Avoid kinking or bending the cable sharply. Store in a dry, cool place away from direct sunlight and extreme temperatures.
Nyocha: Regularly inspect the cable, connectors, and control box for any signs of wear, damage, or corrosion. If any damage is found, discontinue use and contact customer support.

Image showing the EV charger stored neatly in a car trunk, emphasizing portability and ease of storage — This image demonstrates the ease of storage and portability of the ShockFlo EV charger, showing it neatly packed in its storage bag within a car's trunk.

Close-up of the Type 2 connector plugged into a car, highlighting the IP67 waterproof feature — A nso-elu view of the Type 2 connector engaged with a vehicle's charging port, emphasizing the IP67 waterproof rating, which protects against dust and water ingress.

7. Nchọpụta nsogbu

If you encounter issues, refer to the following table. If the problem persists, contact customer support.

Nsogbu	Ihe nwere ike ime	Ngwọta
Chaja anaghị arụ ọrụ	No power from socket; CEE plug not fully inserted; internal fault.	Check power outlet; ensure CEE plug is fully inserted; try a different outlet.
Red indicator light flashing (Error)	Overcurrent, overvoltage, na -agbadatage, overheating, ground fault, leakage current, or other safety protection triggered.	Disconnect charger from vehicle and power source. Wait a few minutes, then reconnect. Check for visible damage to cable/connectors. Ensure vehicle's charging port is clean. If error persists, contact support.
Ịchaji anaghị amalite	Type 2 connector not fully inserted; vehicle not ready to charge; delayed start set; current too low for vehicle.	Ensure Type 2 connector is securely latched; check vehicle's charging status; verify delayed start setting; adjust current to a higher setting if necessary.
Ọsọ nchaji dị nwayọ	Current setting is low; vehicle's onboard charger limitation; power supply limitation.	Increase current setting on the control box (if safe for your circuit); consult your vehicle's manual for charging capabilities.

8. Nkọwapụta

Njirimara	Nkọwapụta
Ụdị	ShockFlo
Aha Nlereanya	Ụdị chaja EV 2
Nọmba ngwaahịa	CG07
Ntinye Voltage	230 volts
Mmepụta Voltage	230 volts
Ampoge	32 Amperes (Adjustable: 10A, 16A, 20A, 24A, 32A)
Wattage / Ike	7 kW
Ogologo eriri USB	6 mita
Ụdị njikọ	CEE 1-phase plug to Type 2 vehicle connector
Ndakọrịta	All Type 2/CCS charging ports (e.g., Volkswagen, Tesla, Renault, Hyundai, SMART, Opel, Skoda, BMW)
Asambodo nchekwa	IEC 62196-2 compliant, TUV certified
Ogo nchekwa	IP67 (ihe na-egbochi mmiri na uzuzu uzuzu)
Akụkụ ngwaahịa	44 x 34 x 13 cm
Ibu ngwaahịa	5 n'arọ

9. Akwụkwọ ikike na nkwado

ShockFlo products are manufactured to high-quality standards. For warranty information, technical support, or any questions regarding your EV charging cable, please contact ShockFlo customer service through the retailer where you purchased the product or visit the official ShockFlo websaịtị maka nkọwa kọntaktị.

Please have your product model number (Type 2 EV Charger) and purchase date available when contacting support.

ShockFlo Type 2 EV Charger