eSUN eBox-Lite-US
eSUN eBOX Lite Upgraded 3D Printing Filament Dryer Box User Manual
Model: eBox-Lite-US
1. Ngwaahịa gafereview
The eSUN eBOX Lite is an upgraded filament dryer box designed to maintain optimal conditions for 3D printing filaments. It effectively removes moisture, preventing common printing issues such as stringing, clogging, and poor adhesion. This device also functions as a filament storage box and spool holder, providing a comprehensive solution for filament management.
Key features include efficient heating, even temperature distribution, low-noise operation, and broad compatibility with various filament types and spool sizes.
Figure 1: eSUN eBOX Lite Filament Dryer Box with a red filament spool inside.
2. Ihe ngwugwu
Chọpụta na ihe niile dị na ngwugwu:
- eBOX Lite Dryer Box
- Power Adapter (US Plug)
- User Manual (this document, and a physical copy)
- Filament Outlet Tube/Bayonet
Figure 2: Illustration of the eBOX Lite and its included accessories.
3. Nhazi ntuziaka
- Nkwanye: Place the eBOX Lite on a stable, flat surface away from direct sunlight, heat sources, and excessive humidity. Ensure adequate ventilation around the unit.
- Njikọ ike: Connect the provided power adapter to the DC input port on the back of the eBOX Lite. Plug the adapter into a standard US power outlet (AC100-240V ~ 50/60Hz).
- Na-ebufe eriri:
- Open the transparent lid of the eBOX Lite.
- Place your filament spool onto the internal rollers. Ensure the spool rotates freely. The maximum compatible spool size is Φ200mm (diameter) x 73mm (height).
- Thread the filament through the designated outlet hole on the lid. If using the outlet conduit, attach it to the hole and thread the filament through it.
- Mechie mkpuchi ahụ nke ọma.
Figure 3: Visual guide for connecting power and loading filament.
4. Ntuziaka ọrụ
The eBOX Lite features a simple control panel with a display and buttons for setting temperature and time.
4.1. Ogwe njikwa gafereview
- Ngosipụta: Shows current settings (temperature level, time remaining).
- Bọtịnụ ụkpụrụ: Used to cycle between temperature setting mode and time setting mode.
- Bọtịnụ elu/ala: Used to adjust values (temperature level, time).
4.2. Setting Temperature and Time
- Ike Na: After connecting the power, the display will light up.
- Set Temperature Level:
- Pịa Ụdị button once to enter temperature setting mode. The display will show a number (1, 2, or 3).
- Jiri ihe Elu/ala buttons to select the desired temperature level based on your filament type:
- Ọkwa 1: Approximately 40°C (suitable for PLA/PLA+)
- Ọkwa 2: Approximately 50°C (suitable for ABS/ABS+/PETG)
- Ọkwa 3: Approximately 55°C (suitable for PVA/Nylon/PC)
- Pịa Ụdị button again to confirm the temperature level and proceed to time setting.
- Set Heating Time:
- The display will now show the time setting (e.g., "00.0h").
- Jiri ihe Elu/ala buttons to set the desired heating duration from 0 to 18 hours. For optimal drying, eSUN recommends at least 2 hours for most filaments.
- Pịa Ụdị button again to start the drying process. The display will show the remaining time.
The eBOX Lite will maintain the set temperature and humidity throughout the drying cycle. Once the time expires, the heating will stop, but the box will continue to provide a dry storage environment.
Figure 4: Recommended temperature levels and corresponding filament types.
Figure 5: Graph illustrating humidity reduction over time during drying.
5. Nlekọta
Regular maintenance ensures the longevity and optimal performance of your eBOX Lite.
- Nhicha: Wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the unit is unplugged before cleaning.
- Nchacha nke ime: Periodically check the inside of the box for any dust or filament debris. Use a soft brush or compressed air to remove any accumulation.
- Nchekwa: Mgbe ejighị ya ogologo oge, wepụ ngwaọrụ ahụ ma chekwaa ya n'ebe dị jụụ na nkụ.
6. Nchọpụta nsogbu
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Ngwaọrụ anaghị agbanwu ọkụ. | Njikọghị ihe nkwụnye ọkụ eletrik ma ọ bụ nsogbu; nsogbu nke ebe ọkụ eletrik. | Ensure power adapter is securely connected. Try a different power outlet. Check if the power adapter is damaged. |
| Filament not drying effectively. | Incorrect temperature level set; insufficient drying time; lid not closed properly. | Verify the correct temperature level for your filament type. Increase drying time (e.g., to 4-6 hours or more for very wet filament). Ensure the lid is fully closed. |
| Ngosipụta bụ oghere ma ọ bụ anaghị anabata ya. | Temporary software glitch; power interruption. | Unplug the device, wait 30 seconds, then plug it back in. If the issue persists, contact customer support. |
| Filament spool does not rotate smoothly. | Spool too large or not seated correctly; debris on rollers. | Ensure spool dimensions are within specifications (Φ200mm x 73mm). Re-seat the spool. Clean the rollers. |
7. Nkọwapụta
| Oke | Uru |
|---|---|
| Nọmba nlereanya | eBox-Lite-US |
| N'ime oke okpomọkụ | 40°C - 55°C |
| Hot Plate Temperature | 105°C - 118°C |
| Enyere ike | AC100-240V ~ 50/60Hz |
| Mpụta ike | DC24V ~ 2A |
| Ike nke Igwe ọkụ | 35W |
| Ibu ngwaahịa | 0.75 n'arọ (1.65 pound) |
| Nha ngwaahịa | 215 x 104 x 238.5 mm |
| Akụkụ ngwugwu | 10.91 x 10 x 5.51 sentimita asatọ |
| Max Spool Capacity | Φ200mm (diameter) x 73mm (height) |
| Compatible Filament Diameter | 1.75mm / 2.85mm / 3.00mm |
| Ụdị ihe | Polycarbonate |
Figure 6: Detailed product specifications and package contents.
8. Akwụkwọ ikike na nkwado
For warranty information and technical support, please refer to the official eSUN websaịtị ma ọ bụ kpọtụrụ ndị ahịa ha ozugbo. Debe nnata nzụta gị ka ihe akaebe nke ịzụrụ.
You can also find additional resources and a PDF version of the user manual at: eSUN eBOX Lite User Manual (PDF)
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.