Integy 2 Output LED On/Off RC Board (Model C29429) User Manual

Okwu mmalite

This manual provides detailed instructions for the installation, operation, and maintenance of your Integy 2 Output LED On/Off RC Board, Model C29429. This device is designed to provide simple on/off control for LED lighting systems in your RC vehicle via the receiver's third channel.

Ozi nchekwa

Kwupu ike mgbe niile tupu ịwụnye ma ọ bụ wepụ ihe mejupụtara ya.
Ensure correct polarity when connecting wires to prevent damage to the board or LEDs.
Keep the board away from water, moisture, and extreme temperatures.
This product is intended for adult use or under adult supervision.
Do not attempt to modify the board, as this may void the warranty and cause malfunction.

Ihe ngwugwu

The package for the Integy 2 Output LED On/Off RC Board (C29429) typically includes:

1x Integy 2 Output LED On/Off RC Board (Model C29429)
Additional components as shown in the product packaging.

Integy 2 Output LED On/Off RC Board, front view

Foto: N'ihu view of the Integy 2 Output LED On/Off RC Board, Model C29429.

Nkọwapụta

Njirimara	Nkọwa
Nọmba nlereanya	C29429
Ụdị	Integy
Nsonaazụ	2 (for LED lights)
Ọwa njikwa	Receiver 3rd Channel
Ụdị ihe	Ọla
Ibu Ibu	4.54 g
Akụkụ akụkụ	1 x 1 x 1 sentimita (ihe dị ka)
Mgbakọ chọrọ	Ee
Afọ nke nrụpụta kacha nta	Ọnwa 180 (afọ 15)

Ntọala na nwụnye

Follow these steps to properly install your Integy 2 Output LED On/Off RC Board:

Prepare your RC Vehicle: Ensure your RC vehicle's power is off and the battery is disconnected before beginning installation.
Locate the 3rd Channel: Identify the available 3rd channel port on your RC receiver. This port is typically labeled "CH3" or similar.
Connect the RC Board: Plug the servo connector from the Integy LED board into the 3rd channel port of your receiver. Ensure the connector is oriented correctly (signal, positive, negative).
Connect LEDs: Connect your LED light sets to the two output ports on the Integy board. Observe correct polarity for your LEDs. Most RC LEDs are designed to plug directly into these types of outputs.
Secure the Board: Mount the Integy board securely within your RC vehicle using double-sided tape or a suitable mounting method, ensuring it is protected from vibrations and moisture.
Nnwale izizi: Reconnect your RC vehicle's battery and power on your transmitter and receiver.

Integy 2 Output LED On/Off RC Board with wiring

Image: The Integy RC board showing connection points for receiver and LED outputs.

Integy 2 Output LED On/Off RC Board, side view

Foto: Akụkụ view of the Integy RC board, highlighting its compact design.

Ntuziaka ọrụ

Once installed, operating the LED lights with your Integy RC Board is straightforward:

Ike Na: Turn on your RC transmitter, then your RC vehicle's receiver.
Control via 3rd Channel: Use the switch or button assigned to the 3rd channel on your RC transmitter to toggle the connected LED lights on or off. The exact control mechanism depends on your specific transmitter model.
Nyochaa arụmọrụ: Confirm that your LED lights illuminate when the 3rd channel is activated and turn off when deactivated.

Nlekọta

To ensure the longevity and optimal performance of your Integy 2 Output LED On/Off RC Board, follow these maintenance guidelines:

Nhicha: Periodically inspect the board for dust or debris. Use a soft, dry brush or compressed air to gently clean the surface. Avoid using liquids or solvents.
Nchekwa: When not in use, store the board in a dry, cool environment, away from direct sunlight and extreme temperatures.
Lelee njikọ: Regularly check all connections to ensure they are secure and free from corrosion.

Nchọpụta nsogbu

If you encounter issues with your Integy 2 Output LED On/Off RC Board, refer to the following common problems and solutions:

Nsogbu	Ihe nwere ike ime	Ngwọta
Ọkụ LED anaghị agba.	Waya/polarity na-ezighi ezi. Loose connection to receiver or LEDs. 3rd channel not activated on transmitter. Faulty LEDs. Enweghị ike ịnata.	Verify all connections and ensure correct polarity. Check that the board is securely plugged into the receiver's 3rd channel. Confirm the 3rd channel switch/button on your transmitter is in the correct position. Test LEDs directly if possible. Hụ na e tinyere ihe nnata ahụ n'ọrụ.
LEDs flicker or are dim.	Ọkụ ọkụ na-ezughị oke. Njikọ rụrụ arụ.	Lelee voltage supply to your receiver and ensure it is adequate for the LEDs. Inspect all wiring for secure connections.
Board gets excessively hot.	Overload from too many/incorrect LEDs. Circuit dị mkpirikpi.	Disconnect power immediately. Review the specifications of your LEDs and ensure they are compatible with the board's output. Inspect for any short circuits in the wiring.

Akwụkwọ ikike na nkwado

Akwụkwọ ikike: This Integy product is covered by a 30-day warranty against manufacturer defects from the date of purchase. This warranty does not cover damage caused by misuse, improper installation, unauthorized modification, or normal wear and tear.

Nkwado ndị ahịa: For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Integy customer support through their official website or the retailer where the product was purchased. Please have your model number (C29429) and proof of purchase ready.

Integy C29429