Peaktech P2170 LCR Meter Instruction Manual

1. Okwu mmalite

The Peaktech P2170 is a digital LCR meter with Equivalent Series Resistance (ESR) measurement capabilities. Designed for both component testing in professional environments and for service and maintenance tasks, its compact design and advanced features ensure precise measurements.

Key features include an illuminated multifunction display with a bargraph and a high measurement frequency of up to 100 kHz. The device also supports PC connectivity for data storage and analysis using the included software.

2. Ozi nchekwa

Na-edebe nchekwa nchekwa ndị a mgbe niile iji gbochie mmerụ ahụ ma ọ bụ mebie ngwaọrụ:

• Read the entire manual before operating the device.
• Do not operate the meter if it appears damaged or if the insulation is compromised.
• Ensure correct battery installation and replacement.
• Avoid contact with live circuits when connecting or disconnecting test leads.
• Do not exceed the maximum input ratings specified for each function.
• Debe ngwaọrụ akọrọ ma dị ọcha.

3. Ngwaahịa gafereview

The Peaktech P2170 LCR Meter is a handheld device designed for measuring inductance (L), capacitance (C), and resistance (R), along with other parameters like ESR, DCR, Dissipation Factor (D), Quality Factor (Q), and Phase Angle (θ).

Foto 1: N'ihu view of the Peaktech P2170 LCR Meter, showing the display, function buttons, and input terminals.

3.1 Akụrụngwa na Ngwa

Ngwungwu ọkọlọtọ gụnyere ihe ndị a:

• Peaktech P2170 LCR Meter
• eriri USB interface
• PC software
• Kelvin clips (test leads)
• Ihe nchekwa nchekwa
• AAA batteries (6x 1.5V)
• Akwụkwọ ntuziaka

Figure 2: Peaktech P2170 LCR Meter shown with its included accessories, including Kelvin clips, USB cable, and software CD.

4. Nhazi

4.1 Ntinye batrị

The device operates on 6 x 1.5V AAA batteries. To install or replace batteries:

1. Jide n'aka na agbanyụrụ mita ahụ.
2. Chọta mkpuchi nke ebe batrị dị n'azụ ngwaọrụ ahụ.
3. Open the cover and insert 6 AAA batteries, observing the correct polarity markings.
4. Mechie mkpuchi nke batrị batrị nke ọma.

An optional 12V 500mA power adapter can also be used for external power.

4.2 Njikọ Ndị Nnwale Nlele

Use the provided Kelvin clips for accurate measurements. Connect them to the input terminals as follows:

• Connect the red Kelvin clip to the Hpot na Hụrụ ọnụ ọnụ.
• Connect the black Kelvin clip to the Lpot na Lcur ọnụ ọnụ.
• For 2-wire measurements, connect the test leads to Hpot na Lpot.
• Ensure a secure connection to minimize measurement errors.

4.3 Software Installation (PC Link)

The included PC software allows for data logging and analysis. Follow these steps to install:

1. Insert the software CD into your computer's optical drive.
2. Soro ntuziaka ihuenyo iji mezue nrụnye.
3. Connect the meter to your PC using the supplied USB interface cable.
4. Launch the software and establish communication with the device. Refer to the software's help documentation for detailed usage.

5. Ntuziaka ọrụ

5.1 Gbanyụọ/ gbanyụọ

Pịa IKE bọtịnụ iji gbanye ma ọ bụ gbanyụọ mita ahụ.

Ụdị nha 5.2

The P2170 supports various measurement modes. Press the ỌUNụ button to cycle through the primary measurement parameters:

• Ls (Series Inductance)
• Cs (Series Capacitance)
• Lp (Parallel Inductance)
• Cp (Parallel Capacitance)
• DCR (DC Resistance)
• ESR (Equivalent Series Resistance)
• Rp (Parallel Resistance)
• D (Dissipation Factor)
• Q (Quality Factor)
• θ (Phase Angle)

The illuminated display will show the selected mode and measurement results.

5.3 Measurement Frequency Selection

Pịa FREQ button to select the desired test frequency. Available frequencies include 100 Hz, 120 Hz, 1 kHz, 10 kHz, and 100 kHz. The chosen frequency will be displayed on the screen.

5.4 Data Jide Ọrụ

Pịa Jide button to freeze the current measurement reading on the display. Press it again to release the hold function.

5.5 nhazi nhazi

To perform a calibration, ensure no component is connected to the input terminals. Press and hold the CAL button for approximately 2 seconds. Follow any on-screen prompts.

6. Nlekọta

6.1 Nhicha

Hichapụ mita ahụ casing jiri nwayọ, damp cloth. Do not use abrasive cleaners or solvents. Ensure the device is powered off and disconnected from any power source before cleaning.

6.2 nnọchi batrị

When the low battery indicator appears on the display, replace all 6 AAA batteries as described in Section 4.1.

6.3 Nchekwa

If the meter is not used for an extended period, remove the batteries to prevent leakage. Store the device in its protective carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.

7. Nchọpụta nsogbu

If you encounter issues with your Peaktech P2170, refer to the following common problems and solutions:

• Meter does not power on: Check battery installation and ensure batteries are not depleted. Try replacing with new batteries.
• Ọgụgụ na-ezighi ezi:
  • Gbaa mbọ hụ na ejikọtara ụzọ nnwale nke ọma ma ghara imebi.
  • Perform a calibration (Section 5.5).
  • Verify the correct measurement mode and frequency are selected for the component being tested.
  • Ensure the component is properly connected to the Kelvin clips.
• PC software not connecting:
  • Lelee njikọ eriri USB.
  • Ensure the software drivers are correctly installed.
  • Restart both the meter and the PC.

If the problem persists, contact Peaktech customer support.

8. Nkọwapụta

Detailed technical specifications for the Peaktech P2170 LCR Meter:

Figure 3: Detailed specifications table for the Peaktech P2170 LCR Meter, including measurement modes, ranges, frequencies, and physical characteristics.

9. Akwụkwọ ikike na nkwado

For warranty information, technical support, or service inquiries, please contact Peaktech directly or refer to their official websaịtị. Debe nnata nzụta gị ka ihe akaebe nke ịzụrụ.