Hicon Ice Maker with LED Display and 2-in-1 Water Dispenser

Okwu mmalite

Thank you for choosing the Hicon Ice Maker with 2-in-1 Water Dispenser. This appliance is designed to provide convenient access to ice and cold water. Please read this manual thoroughly before operating the unit to ensure safe and efficient use. Keep this manual for future reference.

Ntuziaka nchekwa

• Hụ na e tinyere ngwa ahụ n'elu ebe kwụsiri ike, nke dị larịị, nke na-adịghị anya site na ìhè anyanwụ kpọmkwem na ebe okpomọkụ.
• Ejila ngwa, eriri ọkụ, ma ọ bụ nkwụnye na mmiri ma ọ bụ mmiri mmiri ndị ọzọ.
• Debe ụmụaka pụọ ​​na ngwa ngwa mgbe a na-arụ ọrụ.
• Jiri naanị mmiri a na-aṅụ aṅụ na ihe na-eme ice.
• Wepụ ihe mkpuchi ahụ tupu ị sachaa ya ma ọ bụ mgbe a naghị eji ya ruo ogologo oge.
• Do not operate the appliance with a damaged cord or plug. Contact qualified service personnel for repairs.
• Ensure proper ventilation around the unit. Maintain at least 10 cm of space around the sides and back.

Ngwaahịa gafereview

Familiarize yourself with the components of your Hicon Ice Maker.

Ọgụgụ 1: Nhazi Panel Control
This image displays the control panel with buttons for power, ice size selection (Small, Medium, Large), and water dispensing. Indicator lights show when the ice basket is full, water is needed, or the unit is powered on.

Figure 2: Bullet-Shaped Ice Production
The ice maker produces popular bullet-shaped ice cubes, shown here with a water bottle installed on top for automatic water supply.

Melite

Iwepu na ntinye

1. Remove all packaging materials and inspect the unit for any damage.
2. Place the ice maker on a firm, level surface. Ensure there is adequate ventilation around the unit (at least 10 cm clearance on all sides).
3. Allow the unit to stand upright for at least 2-4 hours before plugging it in, especially if it was transported horizontally. This allows the refrigerant to settle.

Na-agbakwụnye mmiri

The Hicon Ice Maker offers two methods for water supply:

Figure 3: Water Filling Methods
The left side shows automatic water addition using a 5-gallon bottle. The right side shows manual water addition by pouring water into the reservoir.

1. Automatic Water Supply (using a water bottle): Place a standard 2, 3, or 5-gallon water bottle onto the top dispenser opening. Ensure the bottle is securely seated.
2. Enyemaka mmiri nke aka: Open the top lid and pour potable water directly into the water reservoir until it reaches the maximum fill line. Do not overfill.

Mara: The melted ice water is recycled back into the reservoir for subsequent ice production cycles.

Ntuziaka ọrụ

1. Ike Na: Tinye ngwa ahụ n'ime oghere eletriki e ji ala rụọ. Gbanye/ Gbanyụọ button on the control panel to start the unit.
2. Họrọ nha ice: Pịa ICE CUBE SIZE SELECTION button repeatedly to cycle through the available ice sizes: Small (S), Medium (M), and Large (L). The corresponding indicator light will illuminate.
3. Mmepụta ice: The unit will begin the ice-making cycle. The first batch of ice may take 6-10 minutes. Subsequent batches will be produced continuously.
4. Ihe ngosi zuru oke nke ice: Mgbe nkata ice juru, na ICE zuru indicator light will illuminate, and the machine will pause ice production. Remove ice to resume operation.
5. Mmiri mmiritage egosi: Ọ bụrụ na nchekwa mmiri dị ala, nke MGBE MMIRITAGE indicator light will illuminate. Add more water using either the automatic or manual method.
6. Dispense Cold Water: To dispense cold water, place a glass under the cold water tap and press the MMIRI button. The water nozzle can be extended and retracted.
7. Gbanyụọ: Pịa Gbanye/ Gbanyụọ bọtịnụ iji gbanyụọ ngwa ahụ.

Mara: The ice produced can remain in the basket for approximately 1-2 hours if the machine is turned off, but it is not a freezer and ice will eventually melt.

Nlekọta

Nhicha

1. Tupu ihicha: Always unplug the ice maker from the power outlet.
2. Ime nhicha: Remove the ice basket. Clean the interior of the water reservoir and ice-making components with a soft cloth dampened with a mild detergent solution. Rinse thoroughly with clean water.
3. Nchacha mpụta: Jiri nwayọ hichaa elu mpụta, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
4. igbapu: Periodically drain any remaining water from the reservoir using the drain plug located at the bottom or back of the unit (refer to specific model for exact location).
5. First Use Recommendation: For best taste, clean the unit thoroughly before its first use.

Nchekwa

If the ice maker will not be used for an extended period, drain all water, clean the unit, and allow it to dry completely before storing in a cool, dry place.

Nchọpụta nsogbu

Nkọwapụta

• Akara: Hicon
• Ụdị: B07S3JLSKY
• Akụkụ ngwaahịa (D x W x H): 35.7 cm x 42.3 cm x 45.2 cm
• Ike mmepụta ice: Up to 25 kg per 24 hours
• Ikike Nchekwa ice: 1.2 n'arọ
• Wattage: 160 watt
• Voltage: 220 volts
• Igwe nju oyi: R600a
• Ụdị ihe: Plastic
• UPC: 195893458158

Ọgụgụ 4: Akụkụ ngwaahịa
This diagram illustrates the physical dimensions of the ice maker for placement and installation planning.

Akwụkwọ ikike na nkwado

The Hicon Ice Maker comes with a akwụkwọ ikike otu afọ site na ụbọchị ịzụrụ. Akwụkwọ ikike a na-ekpuchi ntụpọ nrụpụta n'okpuru ọnọdụ ojiji nkịtị.

For warranty claims, technical support, or any questions regarding your product, please contact Hicon customer service. Please have your model number (B07S3JLSKY) and proof of purchase ready when contacting support.

Hicon has over 10 years of experience in developing ice machines, ensuring advanced ice-making technology and excellent quality.