RIBIMEX Electric Hoist PE495/990C1 User Manual

1. Okwu Mmalite na Nchekwa

This manual provides essential instructions for the safe and efficient operation, installation, and maintenance of your RIBIMEX Electric Hoist PE495/990C1. Please read this manual thoroughly before using the hoist and keep it for future reference.

Nchekwa Mbụ:

• Always ensure the hoist is securely mounted before operation.
• Do not exceed the maximum load capacity of 495 kg (single line) or 990 kg (double line).
• Nyochaa nkwunye, eriri, na nko maka mmebi tupu ejiri nke ọ bụla.
• Debe aka na uwe rụrụ arụ ka ị ghara imegharị akụkụ ahụ.
• Never operate the hoist if you are under the influence of drugs or alcohol.
• Gbaa mbọ hụ na mpaghara ọrụ ahụ enweghị ihe mgbochi na ndị na-eguzo.
• This electric hoist is designed for lifting and lowering loads. Do not use it for pulling, towing, or lifting people.

Nyocha 1: N'eluview of the RIBIMEX Electric Hoist PE495/990C1, showing the main unit and the wired control pendant.

2. Ngwa ngwaahịa

The RIBIMEX Electric Hoist PE495/990C1 includes the following main components:

• Electric Motor and Gearbox Assembly
• Steel Wire Rope with Rubber Stopper
• Load Hook with Safety Latch
• Control Pendant with Emergency Stop Button
• Pulley Block (for double line operation)
• Mounting Brackets and Hardware (for tube and jib arm fixation)

Ọgụgụ 2: Zuru ezu view of the pulley block and load hook, used to double the lifting capacity.

3. Ntọala na nwụnye

Proper installation is crucial for safe operation. Follow these steps carefully:

1. Ebe Nkwanye: Select a sturdy and stable overhead structure (e.g., a robust beam or jib arm) capable of supporting at least twice the maximum intended load.
2. Nkwanye echekwabara: Use the provided mounting brackets and bolts to firmly attach the hoist to the chosen structure. Ensure all fasteners are tightened securely.
3. Njikọ eletrik: Connect the hoist to a 230 V~50 Hz single-phase power supply. Ensure the power outlet is properly grounded and protected by a circuit breaker.
4. Control Pendant Connection: Ensure the control pendant cable is securely connected to the hoist unit. The cable features a twisted steel wire and a rubber stopper.
5. Nyocha USB: Before first use, uncoil the steel wire rope and inspect it for any kinks, fraying, or damage.
6. Single Line Operation (Max 495 kg): For loads up to 495 kg, attach the load directly to the main hook. The cable length is approximately 12 meters.
7. Double Line Operation (Max 990 kg): For loads up to 990 kg, use the provided pulley block.
   • Attach the pulley block's hook to the load.
   • Loop the steel wire rope through the pulley block.
   • Secure the end of the wire rope to the designated attachment point on the hoist body. This configuration effectively halves the lifting speed but doubles the capacity. The cable length for double line operation is approximately 6 meters.

Figure 3: The electric hoist set up for double line operation using the pulley block. Note the reduced effective lifting height when using the pulley block.

4. Ntuziaka ọrụ

Familiarize yourself with the control pendant before operating the hoist.

1. Ike Na: Ensure the hoist is properly connected to the power supply.
2. Nkwụsị ihe mberede: The control pendant features a red emergency stop button. Press this button immediately in case of an emergency to cut power to the hoist. To reset, twist the button clockwise and it will pop out.
3. Na-ebuli: Press and hold the "UP" button on the control pendant to raise the load.
4. Na-agbada: Press and hold the "DOWN" button on the control pendant to lower the load.
5. Oke ibu:
   • Single Line: Maximum load 495 kg. Lifting speed: 8 m/min.
   • Double Line (with pulley block): Maximum load 990 kg. Lifting speed: 4 m/min.
6. Nchekwa ibu ibu: The hoist is equipped with an overload protection system. If the load exceeds the rated capacity, the hoist may automatically stop. Reduce the load before attempting to operate again.
7. Nchekwa okpomọkụ: The motor has thermal protection. If the motor overheats due to continuous use, it may temporarily shut down. Allow the motor to cool down before resuming operation.
8. End Stop: The hoist has an automatic end stop mechanism to prevent the hook from over-winding at the top limit.

5. Nlekọta

Nlekọta oge niile na-achọpụta ogologo ndụ yana ọrụ nchekwa nke elu gị.

• Nyocha kwa ụbọchị: Before each use, visually inspect the steel wire rope for wear, kinks, or damage. Check the load hook for deformation, cracks, or a faulty safety latch. Ensure all mounting bolts are tight.
• mmanu mmanu: Periodically lubricate the wire rope and moving parts as recommended by a qualified technician.
• Nhicha: Keep the hoist unit clean and free from dust, dirt, and debris. Do not use high-pressure water to clean the electrical components.
• Ndochi eriri USB: If the steel wire rope shows signs of significant wear or damage, it must be replaced by a qualified professional.
• Nlekọta moto: The motor is designed for durability. If unusual noises or performance issues occur, consult a service technician.
• Nchekwa: Mgbe a naghị eji ya, debe ihe e ji ebuga ihe n'ebe kpọrọ nkụ, dị ọcha, nke e chebere pụọ na oke okpomọkụ na mmiri mmiri.

6. Nchọpụta nsogbu

Rụtụ aka na ngalaba a maka okwu nkịtị na azịza ha.

7. Nkọwapụta

8. Akwụkwọ ikike na nkwado

Akwụkwọ ikike: This RIBIMEX Electric Hoist PE495/990C1 comes with a 2-afọ akwụkwọ ikike from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage resulting from misuse, neglect, unauthorized modifications, or normal wear and tear.

Nkwado: For technical assistance, spare parts, or warranty claims, please contact your retailer or the RIBIMEX customer service department. Please have your model number (PE495/990C1) and proof of purchase ready when contacting support.

Spare parts availability information is not available at this time.