Forney 58402 Electrical Receptacle Instruction Manual

1. Ngwaahịa gafereview

The Forney 58402 is a heavy-duty Bakelite pin-type wall electrical receptacle designed for surface mounting. It features a 2-pole/3-wire grounding configuration, suitable for high-power applications. This receptacle is rated for 50 Amps at 125/250 Volts and conforms to NEMA 6-50 standards.

Akụkụ ndị bụ isi:

• Heavy duty Bakelite pin-type design for durability.
• Wall electrical receptacle for surface mounting.
• 2-pole/3-wire grounding for enhanced safety.
• 50 Amp with 125/250-Volt capacity.
• NEMA 6-50 electrical configuration.

Foto 1: N'ihu view of the Forney 58402 Electrical Receptacle, showing the pin configuration and voltage/ampọkwa erage.

2. Ozi nchekwa

Ịdọ aka ná ntị: Electrical work can be hazardous. Always disconnect power at the circuit breaker or fuse box before installing, servicing, or removing this receptacle. Failure to do so may result in serious injury or death. If you are unsure about any part of these instructions, consult a qualified electrician.

• Hụ na e soro iwu eletriki niile dị na mpaghara na mba.
• Jiri ngwa nchekwa onwe onye kwesịrị ekwesị (PPE), dị ka uwe aka mkpuchi na ugogbe nchekwa.
• Nyochaa voltage na amperage of your circuit match the receptacle's ratings (50A, 125/250V).
• Do not use this receptacle if it appears damaged.
• Debe ụmụaka pụọ ​​na nrụnye ọkụ eletrik.

3. Ntọala na nwụnye

This section provides general guidelines for installing the Forney 58402 wall receptacle. Specific wiring configurations may vary based on local codes and existing electrical systems.

Ngwaọrụ na Akụrụngwa chọrọ:

• Screwdrivers (Phillips na Flathead)
• Waya waya
• Voltagọ bụ onye nyocha
• Mounting screws (appropriate for surface)
• Electrical box (if not already present)

Nzọụkwụ nwụnye:

1. Kwụpụ ike: Locate the circuit breaker or fuse controlling the circuit where the receptacle will be installed and turn it OFF. Verify power is off using a voltagọ bụ onye nyocha.
2. Kwadebe elu elu: Ensure the surface is clean, dry, and structurally sound. The receptacle is designed for surface mounting.
3. Mount the Receptacle Base: Position the receptacle base on the desired surface. Use appropriate mounting screws to secure it firmly. The back of the receptacle features pre-drilled holes for this purpose.


Ọgụgụ 2: Azụ view of the Forney 58402 Receptacle, showing the metal mounting plate and screw holes for surface installation.

4. Njikọ waya: This receptacle is a 2-pole/3-wire grounding type (NEMA 6-50). It typically requires two hot wires (L1, L2) and one ground wire.
• Strip approximately 1/2 inch of insulation from each wire.
• Connect the L1 (Hot) wire to one of the brass-colored terminals.
• Connect the L2 (Hot) wire to the other brass-colored terminal.
• Connect the Ground wire (typically green or bare copper) to the green hexagonal grounding screw.


Onyonyo 3: N'okpuru view of the Forney 58402 Receptacle, illustrating the internal wiring access points and terminals.

5. Ọkụ echekwabara: Ensure all wire connections are tight and secure. No bare wire should be exposed outside the terminals.
6. Gbakọtaghachi: Carefully place the cover over the wired base and secure it with the provided screws.
7. Weghachi ike: Once installation is complete and verified, turn the power back ON at the circuit breaker or fuse box.

4. Ntuziaka ọrụ

The Forney 58402 Electrical Receptacle is designed for straightforward operation.

1. Nyochaa ndakọrịta: Ensure the plug of your electrical device is compatible with the NEMA 6-50 configuration of this receptacle.


Ọgụgụ 4: nso nso view of the Forney 58402 Receptacle's pin configuration, showing the 50A 250V markings.

2. Fanye nkwụnye: Align the pins of your device's plug with the slots on the receptacle and firmly insert the plug.
3. Wepụ Plọg: To disconnect, grasp the plug firmly and pull it straight out from the receptacle. Do not pull by the cord.

5. Nlekọta

Regular inspection and basic maintenance will help ensure the longevity and safe operation of your Forney 58402 receptacle.

• Nyocha oge: Annually inspect the receptacle for any signs of damage, cracks, discoloration, or loose connections.
• Nhicha: With power disconnected, gently wipe the exterior of the receptacle with a dry, clean cloth to remove dust or debris. Do not use liquid cleaners.
• Mechie njikọ: If comfortable and with power disconnected, periodically check and tighten the terminal screws to ensure secure wire connections.
• Nchekwa gburugburu: Ọ bụrụ na etinyere na mgbasa oziamp or dusty environment, ensure the receptacle is adequately protected from moisture and excessive dust accumulation.

6. Nchọpụta nsogbu

If you experience issues with your Forney 58402 receptacle, consider the following common troubleshooting steps:

If troubleshooting steps do not resolve the issue, or if you are unsure, contact a qualified electrician.

7. Nkọwapụta

8. Akwụkwọ ikike na nkwado

Specific warranty details for the Forney 58402 Electrical Receptacle are not provided in this manual. For warranty information, technical support, or service inquiries, please refer to the product packaging or contact Forney customer service directly.

You may visit the official Forney websaịtị maka ozi kọntaktị na akụrụngwa ndị ọzọ: www.forneynd.com