Clover B14A Hot and Cold Bottled Water Dispenser User Manual

1. Okwu mmalite

The Clover B14A Hot and Cold Bottled Water Dispenser provides convenient access to refreshing chilled drinking water and piping hot water. Designed for home or office use, this dispenser features hygienic stainless steel tanks and an efficient cooling and heating system. Please read this manual thoroughly before operation to ensure safe and optimal performance.

2. Ozi nchekwa

• Nchekwa Eletriki: This appliance operates on 110-120 volts, 50-60 Hz. Ensure the power outlet is properly grounded. Do not use with damaged cords or plugs.
• Nchekwa mmiri ọkụ: The hot water temperature reaches approximately 185°F (85°C). Exercise extreme caution when dispensing hot water to prevent burns. A safety switch is provided for the hot water dispenser.
• Nchekwa ụmụaka: Always engage the hot water safety switch when children are present to prevent accidental dispensing of hot water.
• Nkwanye: Place the dispenser on a flat, stable surface away from direct sunlight, heat sources, and areas with high humidity. Ensure adequate ventilation around the unit.
• Kalama mmiri: Use only standard 5-gallon (18.9-liter) water bottles.
• Nlekọta: Kwupu ngwa ngwa tupu ihicha ma ọ bụ ịrụ ọrụ ọ bụla.

3. Nhazi

1. Iwepu: Carefully remove the dispenser from its packaging. Inspect for any damage.
2. Nkwanye: Position the dispenser on a level, sturdy surface. Allow at least 4 inches (10 cm) of clearance from walls for proper ventilation.
3. Wụnye Tray Drip: Insert the concealed, lift-out drip tray into its designated slot below the spigots.
4. Nhicha izizi: Before first use, clean the exterior with a soft, damp akwa .
5. Wụnye karama mmiri: Remove the protective seal from a new 5-gallon water bottle. Lift the bottle and quickly invert it, placing it firmly onto the bottle support on top of the dispenser. Ensure the bottle is seated correctly to prevent leaks.
6. Sistemụ mkpofu: Before plugging in, dispense at least 1 liter (approximately 4 cups) of water from both the hot and cold spigots to ensure the tanks are filled and to flush any air from the system.
7. Tinye: Plug the power cord into a grounded 110-120V electrical outlet.

Onyonyo 1: Zuru ezu view of the Clover B14A water dispenser with a 5-gallon bottle.

4. Ntuziaka ọrụ

1. Ike Na: Once plugged in, the dispenser will begin cooling and heating the water. Allow approximately 15-30 minutes for the water to reach desired temperatures.
2. Na-ekesa mmiri oyi: Place your cup under the cold water spigot (typically blue). Push the lever to dispense cold water. Release the lever to stop.
3. Na-ekesa mmiri ọkụ: Place your cup under the hot water spigot (typically red). To dispense hot water, first push the safety switch (often a red button or lever) and then push the main lever. Release both to stop.
4. Mgbanwe mmiri ọkụ: The hot water function can be turned on or off using the switch located on the back of the unit. Turning it off will prevent the water from heating, saving energy and acting as an additional safety measure.
5. Adjusting Cold Water Temperature: The cold water temperature can be adjusted via a thermostat control, usually located on the back of the unit. It allows for a range of 35.6°F to 53.6°F (2°C to 12°C).

Figure 2: Detail of the hot (red) and cold (blue) water spigots with the hot water safety switch.

5. Nlekọta

• Nchacha tray Drip: The drip tray is removable for easy cleaning. Periodically empty and wash the tray with mild soap and water.
• Nchacha mpụta: Jiri nwayọ hichaa elu mpụta, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
• Ebelata: Over time, mineral deposits may accumulate in the hot water tank. Consult the manufacturer's website or customer support for recommended descaling procedures.
• Ichacha tankị mmiri: For thorough cleaning of the internal water tanks, it is recommended to contact a qualified service technician.

6. Nchọpụta nsogbu

• Anaghị enye mmiri: Ensure the water bottle is properly seated and not empty. Check if the unit is plugged in and powered on.
• Enweghị mmiri ọkụ: Verify the hot water switch on the back of the unit is in the 'ON' position. Check if the thermal reset button (often a small red button on the back) needs to be pressed.
• No Cold Water: Ensure the unit is plugged in and the cold water thermostat is set to a desired temperature.
• Na-agbapụta: Check the water bottle for cracks or improper seating. Ensure the drip tray is correctly installed.
• Mkpọtụ na-adịghị ahụkebe: The unit is designed for quiet operation. If unusual or excessive noise occurs, ensure the unit is on a level surface and not vibrating against a wall. If noise persists, contact customer support.

7. Nkọwapụta

• Ụdị: B14A
• Akụkụ (D x W x H): 12.3" x 12.7" x 37.9" (31.2 cm x 32.3 cm x 96.3 cm)
• Arọ: 32 lbs (14.5 n'arọ)
• Agba: Black with Steel side panels
• Voltage: 110-120V
• Ugboro: 50-60 Hz
• Okpomọkụ mmiri ọkụ: Approximately 185°F (85°C) (non-adjustable)
• Okpomọkụ mmiri oyi: 35.6°F - 53.6°F (2°C - 12°C) (adjustable)
• Compatible Bottle Sizes: galọn 5 (18.9 lita)
• Ihe eji ewu ụlọ: Igwe anaghị agba nchara, Plastic
• Asambodo: CE, NSF, UL, Energy Star Rated
• Ntapu atịpị: Concealed, lift-out design, high impact, durable ABS. Removable, anti-splash grid.

8. Akwụkwọ ikike na nkwado

The Clover B14A Hot and Cold Bottled Water Dispenser comes with a Akwụkwọ ikike nrụpụta afọ 1 nwere oke. For warranty claims, technical assistance, or further inquiries, please contact Clover customer support. Keep your purchase receipt as proof of purchase.