Casio PQ-30B Digital Alarm Clock User Manual

Okwu mmalite

This manual provides detailed instructions for the proper use and maintenance of your Casio PQ-30B Digital Alarm Clock. Please read this manual thoroughly before using the product to ensure correct operation and to prevent damage.

Akpachara anya maka nchekwa

• Ekwela ka elekere ahụ hụ oke okpomọkụ, anwụ kpọmkwem, ma ọ bụ oke iru mmiri.
• Avoid strong impacts or dropping the clock.
• Do not attempt to disassemble or repair the clock yourself. Refer to qualified service personnel.
• Debe batrị ebe ụmụaka na-apụghị iru. Ọ bụrụ na iloro, chọọ nlekọta ahụike ozugbo.
• Tụfuo batrị eji eme ihe dịka iwu mpaghara siri dị.

Ngwa na njikwa

Ihe onyonyo a na-egosiputa ihu view of the Casio PQ-30B digital alarm clock. It features a digital display showing '10:58 PM', a prominent 'SNOOZE/LIGHT' button, and several control buttons and switches at the bottom for setting time and alarm functions.

Familiarize yourself with the following controls:

• Bọtịnụ SOOZE/LIGHT: Activates the snooze function when the alarm sounds or illuminates the display for a few seconds.
• Bọtịnụ MIN: Adjusts minutes during time or alarm setting.
• Bọtịnụ HR: Adjusts hours during time or alarm setting.
• Time/Alarm Mode Selector (Slide Switch):
  • TM SET: Maka ịtọ oge ugbu a.
  • AL SET: For setting the alarm time.
  • UKWU: Normal time display mode.
• Alarm ON/OFF/SNZ Selector (Slide Switch):
  • AL NA: Activates the alarm.
  • AL OFF: Deactivates the alarm.
  • SNZ: Activates the snooze function (alarm will sound again after approximately 8 minutes).
• 12HR/24HR Button: Toggles between 12-hour and 24-hour time formats.

Melite

Ntinye batrị

The clock requires two LR44 batteries (included). To install or replace batteries:

1. Mepee mkpuchi nchekwa batrị dị n'azụ elekere.
2. Insert the two LR44 batteries, ensuring the correct polarity (+/-) as indicated inside the compartment.
3. Mechie mkpuchi nke batrị batrị nke ọma.

Ntọala Oge izizi

After installing batteries, the display will show a default time. Set the current time as follows:

1. Slide the Time/Alarm Mode Selector switch to TM SET.
2. Pịa HR button to set the hour. Hold it down for faster adjustment.
3. Pịa MIN button to set the minutes. Hold it down for faster adjustment.
4. Pịa 12HR/24HR button to select your preferred time format (12-hour with AM/PM indicator or 24-hour).
5. Once the correct time is set, slide the Time/Alarm Mode Selector switch back to AHORR..

Ntuziaka ọrụ

Ịtọ oge mkpu

1. Slide the Time/Alarm Mode Selector switch to AL SET. The alarm time will be displayed.
2. Pịa HR bọtịnụ ka ịtọọ oge oti mkpu chọrọ.
3. Pịa MIN bọtịnụ iji tọọ nkeji mkpu achọrọ.
4. Slide the Time/Alarm Mode Selector switch back to AHORR..

Na-eme ka/ịgbanyụọ mkpu

• To activate the alarm, slide the Alarm ON/OFF/SNZ Selector switch to AL ON. An alarm indicator (often a bell icon or similar) will appear on the display.
• To deactivate the alarm, slide the Alarm ON/OFF/SNZ Selector switch to Akwụsịla AL. The alarm indicator will disappear.

Iji Ọrụ snooze/Ìhè

• Mgbe oti mkpu dara, pịa nwuo/Ìhè button to temporarily stop the alarm. The alarm will sound again after approximately 8 minutes.
• To illuminate the display at any time, press the nwuo/Ìhè button. The light will stay on for a few seconds.
• To stop the alarm completely after it sounds (without snooze), slide the Alarm ON/OFF/SNZ Selector switch to Akwụsịla AL.

Switching 12-Hour / 24-Hour Format

In AHORR. mode, pịa 12HR/24HR button to toggle between the 12-hour format (with AM/PM indicator) and the 24-hour format.

Nlekọta

• Nhicha: Wipe the clock with a soft, dry cloth. Do not use abrasive cleaners or chemical solvents.
• Ngbanwe batrị: Replace batteries when the display becomes dim or the alarm weakens. Always replace both batteries at the same time.
• Nchekwa: If not using the clock for an extended period, remove the batteries to prevent leakage.

Nchọpụta nsogbu

• Ngosipụta ahụ tọgbọ chakoo ma ọ bụ gbaa ọchịchịrị: Check battery installation. Replace batteries if necessary.
• Mkpu anaghị ada ụda: Ensure the Alarm ON/OFF/SNZ Selector switch is set to AL ON. Verify the alarm time is correctly set.
• Incorrect time display: Re-set the current time following the 'Initial Time Setting' instructions.

Nkọwapụta

Akwụkwọ ikike na nkwado

This Casio product is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or contact Casio customer support. Keep your purchase receipt as proof of purchase.